Instruction/ maintenance manual of the product TRW-1 ECS
Go to page of 9
REV.1/ 25/05 Page 1 of 9 Part #17810 TRW-1 INSTAL L ATION AND OPERAT ING INSTRUCTIONS INTRODUCTION This ECS’ s r emote cont r ol system was devel oped to provi de a safe, r eli able, and user -f ri endly remot e control system for gas hea ting appli ances.
REV.1/ 25/05 Page 2 of 9 Part #17810 WALL MOUNTING THE THERMOSTAT 1. The wir eless Ther mostat must be located wit hi n 20’ of the r eceiver , This is the nor ma l operati onal di stance. 2. Remove face f rom backing plat e as shown i n Figure #1 then locat e t he (2 ) two hol es that mount the plat e to the wal l.
REV.1/ 25/05 Page 3 of 9 Part #17810 THERMO UPDAT ING FEATURE –TRANSMITTER – (T/S –T X) This ECS r em ote cont r ol has a THERMO UPDATING Feature built into it s soft war e.
REV.1/ 25/05 Page 4 of 9 Part #17810 For REMOTE RECEIVERS that operat e on BATTERY POWER, t hese heat condi ti ons can cause batter ies to di schar ge w hen temper atures exceed 115 0 F. Studies show that al kal ine bat t eri es, when exposed t o a constant temperatur e o f 120 0 F , can lose up t o 50% of their operat ing power.
REV.1/ 25/05 Page 5 of 9 Part #17810 To att ach wall cover plat e to receiver box: 1. Posit ion t he receiver as shown i n diagram to the left with lower t ab on wall cover plate int o groove of recei ver (Make sur e ADJ ho le and LEARN hole on cover plat e properl y aligns wit h remot e receiver) 2.
REV.1/ 25/05 Page 6 of 9 Part #17810 WIRI NG ELECTRONIC SPARK IGNITIONS The remot e control receiver can be connected, in seri es, to a 24VAC tr ansf or mer to t he TR (t ransf o rmer) term i nal on the ELECTRONIC MODULE. Conn ect t he hot wi r e from the 24VAC tr ansformer to eit he r of the wir e ter minal s on the rem ot e receiver.
REV.1/ 25/05 Page 7 of 9 Part #17810 The micr oprocessor t hat contr ols the secur ity code matching procedur e is contr oll ed by a ti m i ng functi on.
REV.1/ 25/05 Page 8 of 9 Part #17810 SPECIFI CATIONS BATTERIES: Wal l Tr ansmitter 6 – 2ea. (CR2032) 3.0 volt lithium but ton cell batteri es Remo te Recei v er 6V –4ea. AA 1. 5 Alkaline FCC ID No.’s: transmi t te r –(K9L TS- R-2A); recei ver – (K9L 3001 RX) Operat ing Frequency: 303.
REV.1/ 25/05 Page 9 of 9 Part #17810 RE MOTE WALL TH ER MOS TA T RE CE IVE R INSTAL LATION INST RUCTIONS 16660 EFFECTIVE DAT E JUN E 2004 Remot e W all Therm ost a t Receiver - Cast Iron Series Use the f ollowing st eps to attach the remote r eceiver to the cast ir on stoves: 1.
An important point after buying a device ECS TRW-1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ECS TRW-1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ECS TRW-1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ECS TRW-1 you will learn all the available features of the product, as well as information on its operation. The information that you get ECS TRW-1 will certainly help you make a decision on the purchase.
If you already are a holder of ECS TRW-1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ECS TRW-1.
However, one of the most important roles played by the user manual is to help in solving problems with ECS TRW-1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ECS TRW-1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
