Instruction/ maintenance manual of the product PAS-2601 Echo
Go to page of 16
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 1 P AS Articulating Hedge Clipper Att achment Operator's Manual MODEL 99944200595 FOR MODELS: SRM-2100SB/2400SB SRM-21.
2 Copyright© 2009 By Echo, Incorporated All Rights Reserved. I NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job-dependability. Read and understand this manual included with your attachment.
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 3 Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you.
4 Physical Condition Your judgment and physical dexterity may not be good: • if you are tired or sick, • if you are taking medication, • if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well. Eye Protection Wear eye protection that meets ANSI Z87.
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 5 DANGER Do not operate this product indoors or in inadequately ventilated areas.
6 EQUIPMENT • Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed. • Never adjust blades when the engine is operating. • Inspect hand guard for damage. Replace if damaged or missing. • Check that the blade assembly is firmly attached and in safe operating condition.
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 7 1. CUTTING BLADES - Double reciprocating blades mounted to a blade support bar. Double sided blades, are capable of cutting on either side of the blade. 2. LOWER DRIVE SHAFT ASSEMBLY - Includes the Gear Housing assembly, Flexible Drive Cable, Blade and Safety Decals.
8 D C A A SSEMBL Y POWER HEAD SHAFT / LOWER SHAFT ASSEMBL Y A B D E C Tools Required: None Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling. 1 . Set Power Head/Shaft Assembly on a level surface. 2 . Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to lock- out position.
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 9 ADJUSTING CUTTING ANGLE W ARNING Never adjust cutting assembly with engine running. W ARNING Hedge clipper blades are sharp. Always wear gloves when adjusting cutting assembly, otherwise serious injury may result.
10 ROT A TE CUTTER ASSEMBL Y Always use the unit from the right-hand side of your body – NEVER from the left side. Rotate cutter assembly 180 degrees on driveshaft in order to avoid cutting directly above your head, and to avoid contact with hot muffler.
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 11 M AINTENANCE W ARNING Moving parts can amputate fingers or cause severe injuries.
12 IMPORTANT Flat edge of washer (D) must be against drive shaft. A A Gear Housing Level 1. Tools required: Grease Gun, Rag. Parts required: POWER BLENDX TM 14 oz. Cartridge P/N 91015 Grease or Lithium-based Grease. 1 . Clean dirt from grease fittings (A).
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 13 SHARPENING BLADES Level 3. Tools required: Flat file, screwdriver Parts required: None W ARNING Hedge Clipper Blades are very sharp. Wear gloves to protect hands. 1 . Disconnect spark plug wire from spark plug.
14 BLADE ADJUSTMENT Level 2. Tools required: (2) 10 mm Sockets & Extensions Parts required: None W ARNING Hedge clipper blades are very sharp. Touching them may lead to severe personal injury. Use a socket and extension when adjust- ing blade bolts or blade locknuts in order to keep hands at a safe distance from sharp blades.
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 15 Length ------------------------------------------------------- 1016 mm (40.0 in.) Attachment Width ----------------------------------------- 132 mm (5.2 in.) Height ------------------------------------------------------- 127 mm (5.
DEALER? Call 1-800-432-ECHO or www .echo-usa.com CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 Mon - Fri C.S.T. ECHO, INCORPORA TED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047-1564 www .
An important point after buying a device Echo PAS-2601 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Echo PAS-2601 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Echo PAS-2601 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Echo PAS-2601 you will learn all the available features of the product, as well as information on its operation. The information that you get Echo PAS-2601 will certainly help you make a decision on the purchase.
If you already are a holder of Echo PAS-2601, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Echo PAS-2601.
However, one of the most important roles played by the user manual is to help in solving problems with Echo PAS-2601. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Echo PAS-2601 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
