Instruction/ maintenance manual of the product HC-225 Echo
Go to page of 32
W ARNING R ead rules for safe operation and all instructions carefully . ECHO provides this Operator's Manual and a Safety Manual. Both must be read and under - stood for proper and safe operation.
2 Copyright© 2010 By Echo, Incorporated All Rights Reserved. Specications, descriptions and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accesso- ries, and may not include all standard equipment.
H e d g e C l i p p e r 3 O p e r a t O r ' s M a n u a l CAUTION The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition which may lead to minor or moderate personal injury if not avoided.
4 Physical Condition Y our judgment and physical dexterity may not be good: • if you are tired or sick, • if you are taking medication, • if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well. Eye Protection W ear eye protection that meets ANSI Z87.
H e d g e C l i p p e r 5 O p e r a t O r ' s M a n u a l DANGER Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death.
6 PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD) The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emis- sions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as listed in the Maintenance Section of this manual.
H e d g e C l i p p e r 7 O p e r a t O r ' s M a n u a l 6 7 8 9 10 11 12 13 14 15 P/N X505000270 P/N X505000280 Handle Guard P/N X505002310 Hot Decal (near mufer) d e s c r I p t I o n Locate the safety decals on your unit. Make sure the decals are legible and that you understand and follow the instruc- tions on them.
8 1. BLADES - Double reciprocating single side blades mounted to a blade support bar . 2. SUPPOR T HANDLE WITH GUARD - FOR RIGHT HAND - Rubber non-slip grip, guard protects hand from the blades. W arning decals are located on guard. 3. SP ARK PLUG - Provides spark to ignite fuel mixture.
H e d g e C l i p p e r 9 O p e r a t O r ' s M a n u a l c o n t e n t s The ECHO product you purchased has been factory pre-assembled for your convenience. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts.
10 f u e l NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty . Read and follow instructions in the Storage section of this manual.
H e d g e C l i p p e r 11 O p e r a t O r ' s M a n u a l Mixing Instructions 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of 2-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline.
12 s t a r t I n g c o l d e n g I n e W ARNING Hedge Clipper blades are very sharp. T ouching them may lead to severe personal injury . A void touching blades whenever possible, and always wear gloves to protect hands. NOTE The blade cover is used for transportation and storage.
H e d g e C l i p p e r 13 O p e r a t O r ' s M a n u a l s t o p p I n g e n g I n e 1. Throttle Release throttle and allow engine to return to idle before shutting off engine.
14 h e d g e t r I m m I n g m a I n t e n a n c e W ARNING Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all openings.
H e d g e C l i p p e r 15 O p e r a t O r ' s M a n u a l m a I n t e n a n c e I n t e r v a l s s k I l l l e v e l s Level 1 = Easy to do. Common tools may be required. Level 2 = Moderate difculty . Some specialized tools may be required. ECHO offers REPOWER TM Maintenance Kits and Parts to make your maintenance job easier .
16 a I r f I l t e r Level 1. T ools r equir ed: 25 or 50 mm (1 or 2 in.) cleaning brush Parts r equired: REPOWER TM AIR & FUEL FIL TER KIT . 1. Close choke (Cold Start Position [ ]). This prevents dirt from entering the carburetor throat when the air lter is removed.
H e d g e C l i p p e r 17 O p e r a t O r ' s M a n u a l s p a r k p l u g Level 2. T ools r equir ed: T -wrench, Feeler gauge, Soft metal brush Parts r equired: REPOWER TM T une-Up Kit IMPOR T ANT Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) other - wise severe engine damage may occur .
18 A B 1. Remove mufer cover (A). 2. Remove starter cover (B) and clean dirt and dust from ns. IMPOR T ANT DO NOT use a metal scraper to remove dirt from the cylinder ns. 3. Assemble components in reverse order . e x h a u s t s y s t e m Spark Arrestor Screen Level 2.
H e d g e C l i p p e r 19 O p e r a t O r ' s M a n u a l Exhaust Port Cleaning Level 2. T ools r equir ed: 4 mm Hex wrench, W ood or plastic scraper Parts Requir ed: As needed: Heat Shield 1. Remove spark plug lead from spark plug, and remove engine cover (2 screws).
20 High Altitude Operation This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance up to 1,100 feet above sea level (ASL) (96.0 kPa). T o maintain proper engine operation and emis- sion compliance above 1,100 feet ASL the carburetor may need to be adjusted by an authorized ECHO service dealer .
H e d g e C l i p p e r 21 O p e r a t O r ' s M a n u a l l u b r I c a t I o n Blades Level 1. T ools r equir ed: Clean rag, 25 or 50 mm (1 or 2 in.) cleaning brush Parts r equired: 20W Engine Oil (lubrication), 50-50 mixture of kerosene and 20W oil (cleaning).
22 s h a r p e n I n g b l a d e s Level 3. T ools r equir ed: Flat le, Screwdriver Parts r equired: None W ARNING Hedge Clipper blades are very sharp. T ouching them may lead to severe personal injury . A void touching blades whenever possible, and always wear gloves to protect hands.
H e d g e C l i p p e r 23 O p e r a t O r ' s M a n u a l b l a d e a d j u s t m e n t Level 2. T ools r equir ed: (2) 10 mm Sockets and Extensions Parts r equired: None W ARNING Hedge clipper blades are very sharp. T ouching them may lead to severe personal injury .
24 t r o u b l e s h o o t I n g W ARNING Fuel vapors are extremely ammable and may cause re and/or explosion. Never test for ignition spark by ground- ing spark plug near cylinder plug hole, otherwise serious personal injury may result.
H e d g e C l i p p e r 25 O p e r a t O r ' s M a n u a l s t o r a g e W ARNING During operation the mufer or catalytic mufer and surrounding cover become hot. Always keep exhaust area clear of ammable debris during transportation or when storing, otherwise serious personal injury may result.
26 s p e c I f I c a t I o n s MODEL ---------------------------------------------------- HC-225 Length ------------------------------------------------------ 1,086 mm (42.8 in.) W idth -------------------------------------------------------- 251 mm (9.
H e d g e C l i p p e r 27 O p e r a t O r ' s M a n u a l ECHO LIMITED W ARRANTY ST A TEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated’s Limited Warranty , provides to the original purchaser that this ECHO product is free from defe cts in material and workmans hip .
28 PURCHASED REP AIR P ARTS, SHORT BLOCKS AND ACCESSORIES .
H e d g e C l i p p e r 29 O p e r a t O r ' s M a n u a l ECHO INCORPORA TED EMISSION CONTROL W ARRANTY ST A TEMENT FOR ECHO AND SHINDAIW A BRANDS The Environmental Protection Agency (EP A) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.
30 n o t e s.
H e d g e C l i p p e r 31 O p e r a t O r ' s M a n u a l n o t e s.
ECHO, INCORPORA TED 400 O A k w O O D R O A D L A k E Z u R I C H , IL 60047 www .echo-usa.com DEALER? Call 1-800-432-ECHO 1-800-432-3246 or www .echo-usa.
An important point after buying a device Echo HC-225 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Echo HC-225 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Echo HC-225 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Echo HC-225 you will learn all the available features of the product, as well as information on its operation. The information that you get Echo HC-225 will certainly help you make a decision on the purchase.
If you already are a holder of Echo HC-225, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Echo HC-225.
However, one of the most important roles played by the user manual is to help in solving problems with Echo HC-225. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Echo HC-225 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
