Instruction/ maintenance manual of the product HC-1600 - Type 1E Echo
Go to page of 32
Hedge Clipper Operator's Manual MODELS: HC-1500 - T ype 1E Serial Number 001001 & Up HC-1500 - T ype 2E Serial Number 001001 & Up HC-1600 - T ype 1E Serial Number 001001 & Up HC-2000 .
2 I NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job- dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operations tips and SAFETY messages.
H EDGE C LIPPER O PERA TOR ' S M ANUAL 3 Throughout this manual and on the product itself, you will find safety alerts and helpful, information messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you.
4 Symbol description/application Symbol form/shape Symbol description/application Symbol form/shape Hot Surface Carburetor adjustment - Idle speed Carburetor adjustment - High speed mixture Symbol description/application Symbol form/shape Symbol description/application Symbol form/shape Read and understand owners manual.
H EDGE C LIPPER O PERA TOR ' S M ANUAL 5 FUEL W ARNING DANGER Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • Use an approved fuel container. • DO NOT smoke near fuel. • DO NOT allow flames or sparks near fuel.
6 Physical Condition -- Eye Protection -- Eye protection that meet ANSI Z87.1 or CE requirements must be worn whenever you operate the Hedge Clipper. Hand Protection -- Wear no-slip, heavy duty work gloves to improve your grip on the handles. Gloves also reduce the transmission of machine vibration to your hands.
H EDGE C LIPPER O PERA TOR ' S M ANUAL 7 SAFE OPERA TION Determine Operation Area • Do not operate this product indoors or in inadequately ventilated areas. • Review the area to be trimmed. Look for hazards that could contribute to unsafe conditions.
8 EXTENDED OPERA TION / EXTREME CONDITIONS V ibration and Cold It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals may be brought about by exposure to vibration and cold.
H EDGE C LIPPER O PERA TOR ' S M ANUAL 9 D ESCRIPTION The ECHO product you purchased has been factory pre-assembled for your convenience. After opening the carton, check for damage. Immedi- ately notify your retailer or ECHO Dealer of damaged or missing parts.
10 14 18 12 15 8 6 16 11 5 7 17 HC-2000, 2400, 2410 2 1 HC-1500, 1600 3 4 6 7 8 9 10 11 12 13 14 15 16 10 13 19 20.
H EDGE C LIPPER O PERA TOR ' S M ANUAL 11 1. SAFETY MANUAL - Read and understand this manual before operation. Keep manual in a safe location of safe operating techniques. 2. OPERATOR'S MANUAL - Read and understand this manual before operation.
12 S PECIFICA TIONS L E D O ME 1 0 0 5 1 - C H E 2 0 0 5 1 - C H E 1 0 0 6 1 - C HE 1 0 0 0 2 - C HE 1 0 0 4 2 - C H E 2 0 0 4 2 - C H E 1 0 1 4 2 - C H E 2 0 1 4 2 - C H h t g n e Lm m 0 6 9 ) . n i 8 . 7 3 ( m m 3 3 1 1 ) . n i 6 . 4 4 ( m m 0 9 9 ) .
H EDGE C LIPPER O PERA TOR ' S M ANUAL 13 A SSEMBL Y HC MODELS ARE PRE - ASSEMBLED IN THE BOX . Tools Required: None Parts Required: None P RE -O PERA TION FUEL Fuel Requirements Gasoline - Use 89 Octane [ ] (mid grade or higher) gasoline known to be good quality.
14 Handling Fuel W ARNING DANGER Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • Use an approved fuel container. • DO NOT smoke near fuel. • DO NOT allow flames or sparks near fuel.
H EDGE C LIPPER O PERA TOR ' S M ANUAL 15 EQUIPMENT CHECK Before operation a complete check of the unit must be performed; • Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed. • Inspect fuel lines, tank and area around carburetor for fuel leaks.
16 4.5 m (15 ft.) C B COLD START RUN IDLE H L O PERA TION • Provide all users of this equipment with the Operator's Manual and instructions for Safe Operation. • Before starting the unit, equip yourself and any other person working within the 4.
H EDGE C LIPPER O PERA TOR ' S M ANUAL 17 4 . START - PULL ROPE Lay the hedge clipper on a flat clear area and pull the recoil starter handle (D) until engine fires. 5 . OPEN CHOKE - RUN. Move choke (B) to the RUN (OPEN) position. Restart engine if necessary and allow unit to warm up at idle for several minutes.
18 STOPPING ENGINE 1 . RELEASE THROTTLE. Allow engine to idle for a minute. 2 . STOP SWITCH - STOP. Move stop switch (A) to STOP position. W ARNING DANGER If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engine.
H EDGE C LIPPER O PERA TOR ' S M ANUAL 19 MAINTENANCE INTERV ALS m e t s y S / t n e n o p m o C e c n a n e t n i a M e r u d e c o r P e r o f e B e s U y r e v E l e u f e R y l i a D r o y r .
20 AIR FIL TER Level 1. Tools required: 25 or 50 mm (1 or 2 in.) medium bristle paint brush Parts required: 90008 REPOWER TM AIR & FUEL FILTER KIT 1. Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed.
H EDGE C LIPPER O PERA TOR ' S M ANUAL 21 SP ARK PLUG Level 2. Tools required: T-wrench, Feeler gauge, Soft metal brush Parts required: Spark Plug, BPMR-7A 15901010230 1 . Remove spark plug and check for fouling, worn and rounded center electrode.
22 1 . Remove starter and disconnect the throttle cable end from the carburetor. 2 . Remove the two screws that retain the engine cover. Lift the engine cover (A) from the engine and lay aside. NOTE The throttle cable remains assembled to the engine cover (A) and the spark plug lead and grommet remain installed.
H EDGE C LIPPER O PERA TOR ' S M ANUAL 23 1 . Before adjusting the carburetor, clean or replace the air filter and spark arrester screen. 2 . Start engine and run for several minutes to reach operating tempera- ture. 3 . Stop engine. Turn HI (A) speed needle CCW (counter clockwise) to stop.
24 Basic Setting 1 . Stop engine and turn both LO (B) and HI (A) needles in, CW until they stop and are lightly seated. IMPORTANT DO NOT over tighten needles.
H EDGE C LIPPER O PERA TOR ' S M ANUAL 25 LUBRICA TION Blades Level 1. Tools required: Clean rag, 25 or 50 mm (1 or 2 in.) medium bristle paint brush Parts Required: 20W Engine Oil (lubrication), 50-50 mixture of kerosene and 20W oil (cleaning). W ARNING DANGER Hedge Clipper Blades are very sharp.
26 Gear Box Assembly Level 2. Tools required: 3 mm Hexagon wrench, Grease Gun Parts Required: Gear Box Gasket, HC-2400 P/N 61041401260, HC-1500 2E P/N 61041406560, Others P/N 61041405360, ECHO ® LUBE TM 8 oz. (P/N 91014) or Lithium Based Grease. HC-1500 T ype 1, Type 1E 1 .
H EDGE C LIPPER O PERA TOR ' S M ANUAL 27 HC-1500, T ype 2E, HC-2400, 2410 (All) Level 1. Tools required: Grease Gun, Clean rag Parts required: ECHO ® LUBE TM 8 oz. (P/N 91014) or Lithium Based Grease. 1 . Clean dirt from the grease fitting. 2 .
28 SHARPENING BLADES Level 3. Tools required: Flat file, Screwdriver Parts required: None W ARNING DANGER Hedge Clipper Blades are very sharp. Wear gloves to protect hands. 1 . Disconnect spark plug wire from spark plug. 2 . (Models HC-1500, HC-1600) Remove blade stiffener (See "Blade Stiffener Remove/Install" on page 26).
H EDGE C LIPPER O PERA TOR ' S M ANUAL 29 W ARNING DANGER Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug against cylinder, otherwise serious personal injury may result.
30 S TORAGE Long T erm Storage (over 30 days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following: 1 . Store unit in a dry, dust free place, out of the reach of children.
H EDGE C LIPPER O PERA TOR ' S M ANUAL 31 NOTES.
ECHO, INCORPORA TED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047-1564 www .echo-usa.com DEALER? Call 1-800-432-ECHO 1-800-432-3246 www .echo-usa.com CONSUMER PRODUCT SUPPORT 1-800-673-1558 8 - 5 Mon - Fri C.
An important point after buying a device Echo HC-1600 - Type 1E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Echo HC-1600 - Type 1E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Echo HC-1600 - Type 1E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Echo HC-1600 - Type 1E you will learn all the available features of the product, as well as information on its operation. The information that you get Echo HC-1600 - Type 1E will certainly help you make a decision on the purchase.
If you already are a holder of Echo HC-1600 - Type 1E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Echo HC-1600 - Type 1E.
However, one of the most important roles played by the user manual is to help in solving problems with Echo HC-1600 - Type 1E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Echo HC-1600 - Type 1E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
