Instruction/ maintenance manual of the product ED-200 Echo
Go to page of 16
ED-200 ENGINE DRILL X750-004 56 0 X750409-3400 W ARNING D ANGER READ INSTRUCTIONS CAREFULL Y AND FOLLO W RULES FOR SAFE OPERA TION. F AILURE T O DO SO COULD RESUL T IN SERIOUS INJUR Y .
W ARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer , birth defects or other reproductive harm.
1 IMPORTANT The enclosed message provides information necessary for the protection of the unit. NOTE This enclosed message provides tips for use, care and maintenance of the unit. Throughout this manual and on the product itself, you will find safety alters and helpful, information messages preceded by symbols or key words.
2 WARNING DANGER ALWAYS STOP THE ENGINE WHEN A DRILL JAM OCCURS. DO NOT ATTEMPT TO REMOVE AN OBJECT CAUSING A DRILL JAM IF THE ENGINE IS RUNNING. PHYSICAL INJURY CAN OCCUR IF A DRILL JAM IS REMOVED AND THE DRILLS START MOVING. • Do all drilling at full throttle speed.
3 • Wear non-slip, heavy-duty work gloves to improve your grip on the engine drill handles. The gloves also help reduce the transmission of machine vibrations to your hands. PR O TECTING O THERS Spectators, children, fellow workers and animals must be warned to come no nearer than 4.
4 Repetitive Stress Injuries It is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI).
5 • Do not force the drills and only move as quickly as the drills will allow. • Stop the engine and disconnect from ignition cable before: - cleaning or when clearing a blockage; checking, maintenance or working on the machine. • Handle fuel with care; it is highly flammable.
6 DESCRIPTION 1 11 10 5 8 13 14 12 2 3 4 9 7 6 1. Operator’s manual - Included with unit. Read before operation and keep for future reference to learn proper, safe operating techniques. 2. Throttle trigger - Device activated by the operator’s finger, for controlling the engine speed.
7 ASSEMBLING • Insert the front handle to the machine, and turn clockwise. (TIGHTEN THE SCREW FIRMLY) - To operate front handle with right hand, remove right plug then reverse sides when installing handle and plug.
8 IMPORTANT Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use. On Stop Throttle trigger NOTE When engine does not stop, shift choke lever to close position.
9 IMPORTANT Time intervals are maximum. Actual use and your experience will determine the frequency of required maintenance. Record dates of monthly and yearly inspections.
10 TR OUBLE SHOO TING Trouble Engine - starts hard Cause Remedy - does not start Engine Fuel at No fuel • Fuel filter clogged • Clean or replace cranks carburetor at carburetor • Fuel line clogg.
11 MAINTENANCE AIR FIL TER • Clean before Use. - Remove air cleaner cover and pull out air filter. - Lightly brush off dust or wash it in water and detergent. - Dry completely before putting it back in place. Fuel filter Fuel tank cap • Check periodically.
12 ADJUSTING CARBURET OR (As Required) GENERAL INFORMATION The idle speed adjuster screw controls the throttle opening at the idle position. IDLE ADJUSTMENT 1. Start engine and allow it to run at high idle until warm. 2. Turn the idle speed screw clockwise until drill bit begins to move.
13 6. Drain the fuel tank completely and pull the recoil starter handle several times to remove fuel from the carburetor. 7. Remove the spark plug and pour 1/2 tablespoon (1/4 oz) of fresh, clean, 2-stroke engine oil into the cylinder through the spark plug hole.
14 SPECIFICA TIONS ED-200 Mass without drill bit kg 4.4 (9.7 lbs) Volume fuel tank L 0.5 (16.9 US,fl.oz.) Drill size mm 32 - 178 (1.25 - 7 inch) chuck capacity mm 13 (0.5 inch) speed r/min 430 Mission reduction ratio 20.5 lubrication grease External Dimensions length × width × height mm 395 × 325 × 255 without drill bit (15.
An important point after buying a device Echo ED-200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Echo ED-200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Echo ED-200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Echo ED-200 you will learn all the available features of the product, as well as information on its operation. The information that you get Echo ED-200 will certainly help you make a decision on the purchase.
If you already are a holder of Echo ED-200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Echo ED-200.
However, one of the most important roles played by the user manual is to help in solving problems with Echo ED-200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Echo ED-200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
