Instruction/ maintenance manual of the product FF8 Earthquake Sound
Go to page of 16
.
Safety Instructions 13. Damage Requiring Service — The Component 1. Read Instructions — All the safety and operation should be served only by EQ qualified serviced instructions should be read before the Earthquake personnel when: Component is operated.
W ARNING: The MiniMe subwoofers are capable of generating high sound pressure levels. Y ou should exercise caution when operating these speakers. Long term exposures to high levels of sound pressure will cause permanent damage to your hearing.
Earthquake • MiniMe User Manual 4 Introduction Please take a moment to fill out and mail the Earthquake W arranty Registration card. Also read the serial number located on the control panel and record it here: Unpacking Y our Earthquake subwoofer should reach you in perfect condition.
Earthquake • MiniMe User Manual 5 Control Panel Overview (4) Power Status LED (5) Line Level RCA Inputs (6) Sub Operation Switch (7) Auto ON/OFF (8) Speaker Level Inputs (9) Speaker Level Outputs (1.
Earthquake • MiniMe User Manual 6 (7) Auto ON/OFF (1 1) 1 10-120V AC Power When the main “POWER” ON/OFF switch is in the Connection “OFF” position, this switch has no affect on the The Earthquake MiniMe is equipped with a built in subwoofer .
Installation Observe the following general precautions and Route the power-supply cord so it is not likely to be read the safety instructions before powering your walked on or pinched by especially at plugs, Earthquake subwoofer . convenience receptacles, and the point where it exits from the unit.
AC outlets on the same circuit breaker Power strip T ape Deck DVD Pre-amplifier Amplifier Subwoofer Earthquake • MiniMe User Manual 8 • Choose reliable, high quality interconnect cables, Connections also called patch cords or RCA cables.
.
Earthquake • MiniMe User Manual 10 System Configurations The following pages show some typical connections that you might make in your installation. They show how the inputs and outputs of the Earthquake sub are connected to your pre-amplifier or receiver .
Earthquake • MiniMe User Manual 1 1 Connections to a pre-amplifier using “Y” cables If your pre-amplifier does not have a sub/LFE output, you can use “Y” cables to send its main outputs to both the subwoofer and your amplifier . The subwoofer will play the low frequency range and your front speakers will play the full range.
Earthquake • MiniMe User Manual 12 Using the line speaker-level inputs If you are using a receiver which does not have a subwoofer output or line level outputs (pre-outs), you can connect its speaker outputs to the subwoofer's Speaker-Level inputs.
Earthquake • MiniMe User Manual 13 Adjusting the controls There are two main methods for adjusting the level, crossover frequency and phase of the Earthquake MiniMe to match a system. ? Method One: T ypical: Listening and making adjustments to suit your taste.
Specification Amplifier Output 160 W atts RMS (4.6-Ohm impedance) High Cut Filter 35Hz 100Hz adjustable. The crossover can be bypassed by rotating the crossover frequency control fully clockwise. Frequency Response 25Hz 160Hz Power Line V oltage 1 10-120C~AC / 60Hz / 180 W A TTS Dimensions (HxWxD) 10.
Earthquake • MiniMe User Manual 15 Limited 5-Y ear W arranty Earthquake warrants the original purchaser that all Factory Sealed New Audio Products to be free from defects in material and workmanship.
Earthquake Sound Corporation. 2727 Mc Cone Avenue, Hayward, California 94545. Ph (510) 732-1000. Fax (510) 732-1095 www .earthquakesound.com.
An important point after buying a device Earthquake Sound FF8 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Earthquake Sound FF8 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Earthquake Sound FF8 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Earthquake Sound FF8 you will learn all the available features of the product, as well as information on its operation. The information that you get Earthquake Sound FF8 will certainly help you make a decision on the purchase.
If you already are a holder of Earthquake Sound FF8, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Earthquake Sound FF8.
However, one of the most important roles played by the user manual is to help in solving problems with Earthquake Sound FF8. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Earthquake Sound FF8 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
