Instruction/ maintenance manual of the product ASG55 Earlex
Go to page of 12
Thank you for purchasing an Earlex Outdoor Paint Sprayer . Please read all these instructions before operating this product and retain them for future reference. Earlex Ltd will accept no responsibility for the use of this product if used for any other purposes than those detailed herein.
● K eep work area clean - Cluttered areas and benches invite injuries. ● C onsider work area environment - Do not expose the spray gun to rain. Do not use the spray gun in damp o r wet locations. Keep work area well lit. ● G uard against electric shock - Avoid body contact with e arthed or grounded surfaces (e.
1. 1.0mm Nozzle SG209 2. 0.6mm Nozzle SG21 1 3a. V alve Assembly - 3 parts SG612 3b. Piston Spring 55W SG612 3c. Piston Assembly SG612 4. Suction Tube and Filter Assembly SG240 5.
$$ $ #$ "#% $#")%" $# " )"" $##$"%$.
5 Preparation of the surface and thinning of the paint are the two most important areas to be concerned with to obtain the best results from your Paint Sprayer . Ensure all surfaces are free from dust, dirt, rust and grease. If necessary rub down with sandpaper , or similar .
6 T urning the output control knob clockwise reduces the flow of material whilst turning it anti-clockwise increases the flow . T o adjust the pattern undertake the following: 1. Turn the output control knob anti-clockwise to the maximum position. 2. Pull the trigger and test the pattern on a piece of cardboard or newspaper .
1) Only apply one coat at a time. If more than one coat is required follow the paint manufacturer’s instructions for drying times. 2) If spraying small objects keep the output setting low as this will avoid excessive use of paint and will minimise overspray .
8 ● Rinse the Paint Sprayer Paint Container with the t hinner that was used and spray through the Paint S prayer onto cardboard or newspaper . ● Remove the top knob, slightly push the nozzle towards the switch and pull down and forward to release the piston cylinder assembly from the main Paint Sprayer assembly .
9 ● Thoroughly clean all of these parts. Lightly oil the p iston and slide it in and out of the cylinder to d istribute the oil over the mating parts, reassemble all of the components to their original p ositions (see page 8).
10 " %# $ "!%" Paint Sprayer hums but does not operate Piston sticking (3c) Remove the large knob at the top of the unit. Pull Nozzle and Piston Assembly down and back to release from main gun assembly .
1 1 This unit is a Class II appliance which means it is double insulated for your protection, no earthing wire is necessary . If the supply cord is damaged, it must be replaced by Earlex Ltd or our appointed agents. Y our unit has been supplied with a mains lead with a fitted fused plug.
$#.
An important point after buying a device Earlex ASG55 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Earlex ASG55 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Earlex ASG55 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Earlex ASG55 you will learn all the available features of the product, as well as information on its operation. The information that you get Earlex ASG55 will certainly help you make a decision on the purchase.
If you already are a holder of Earlex ASG55, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Earlex ASG55.
However, one of the most important roles played by the user manual is to help in solving problems with Earlex ASG55. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Earlex ASG55 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
