Instruction/ maintenance manual of the product DX-WD1202 Dynex
Go to page of 23
ASSEMBL Y INSTRUC TIONS D X - WD1202 Corner T V Stand Safety information and specifications ............ 2 T ools needed . ........................................................... 3 P ack age contents ...............................................
2 DX-WD1202 Need help? Call 800-305-2204 Safety inf ormation and specifica tions Wa r n i n g s • Do not let children climb on your stand or play near it.
3 DX-WD1202 Need help? Call 800-305-2204 Package co ntents P ackage contents: hardware Note: Y ou may receive ex tra hardware with your ne w T V stand. Make sure you hav e all the hardware ne cessary to assemble your new T V stand: To o l s n e e d e d Hammer No .
4 DX-WD1202 Need help? Call 800-305-2204 P ackage contents: hardwar e (continued) Using a screw that is too long wi ll cause damage to your stand. Bef ore beginning assembly , separate each type of screw . Carefully study the screw tabl e below . Y ou can use the rule r at the bottom of the screw table to measur e screws .
5 DX-WD1202 Need help? Call 800-305-2204 P ackage contents: par ts A End (2) E Bottom (1) F Shelf (1) B Upright (1) C Lo wer upright (1) D To p ( 1 ) G Back (1) H Door (2) I Right fro nt and left rear.
6 DX-WD1202 Need help? Call 800-305-2204 Assembly instructions Step1: Assemble your stand on a carpet ed fl oor or on the empt y car ton to av oid scratching your stand or the floor . Push thirt y hidden cams ( Q ) into the ends ( A ), uprights ( B and C ), t op ( D ), bottom ( E ), shelf ( F ), and one set of legs ( I and J ).
7 DX-WD1202 Need help? Call 800-305-2204 T ightening hidden cams In the re maining steps, use these illustrations f or in structions on tightening hidden cams. Wa r n i n g : Risk of damage or injur y . Hidde n cams must be completely tightened. Hidden cams that are not completely tightened will loosen, and parts may separate.
8 DX-WD1202 Need help? Call 800-305-2204 Step 2: Sc rew two c am scre ws ( S ) into each of the legs (two I and two J ). Place the ends ( A ) flat with the side with the hidden cams facing up. Make sure that the sides of the legs wi th the hidden cams ar e towar d the ends ( A ).
9 DX-WD1202 Need help? Call 800-305-2204 Step 3: Carefully turn the ends ( A ) over so the side without the hidden cams is facing up. Use a Phillips screw driver to screw ei ght black 9/16" flat head scr ews ( FF ) (four per end) into the ends ( A ) until the shoulders of the screws r est on the sur face of the ends.
10 DX-WD1202 Need help? Call 800-305-2204 Step 4: Careful ly turn the ends over so the sides with the hidden cams fac e up. Attach the unattached leg ( I ) to the left end ( A ) and the unattached leg ( J ) to the right end ( A ). See Step 2 for instructions.
11 DX-WD1202 Need help? Call 800-305-2204 Step 5: F asten the stop molding ( L ) to the top ( D ). Use a flatblade screw driver to tight en the four hidden cams .
12 DX-WD1202 Need help? Call 800-305-2204 Step 6: F asten the upright ( B ) and the left end ( A ) with the leg ( J ) to the top ( D ) and stop molding ( L ). Use a flatblade screwdriver to tighten the five hi dden cams (two on the upright ( B ), two on the left end ( A ), and one on the leg ( J )).
13 DX-WD1202 Need help? Call 800-305-2204 Step 7: F asten the shelf ( F ) to the left end ( A ). Use a flatblade screw driver to tight en the two hidden cams. See “Tight ening hidden cams” on page 7. F asten the shelf ( F ) to the upright ( B ). Use a Phillips scr ewdriver and tw o black 1 7/8" flat head scr ews ( DD ).
14 DX-WD1202 Need help? Call 800-305-2204 Step 8: F asten the bottom ( E ) to the left end ( A ). Use a flatblade screwdriv er to tighten the two hidden cams. See “Tightening hidden cams” on page 7. F asten the bottom ( E ) to the lower upright ( C ).
15 DX-WD1202 Need help? Call 800-305-2204 Step 9: F asten the right end ( A ) with the leg ( I ) to the top ( D ), bottom ( E ), shelf ( F ), and stop molding ( L ). Use a flatblade screw driver to tighten the seven hidden cams: A (2), E (2), F (2), and I (1).
16 DX-WD1202 Need help? Call 800-305-2204 Step 10: With the t op of the unit facing down, fasten the foot base ( U ) to the extension block ( K ). Use a Phillips screwdriver and f our black 9/16" pan head screws ( GG ). Then, push the foot ( T ) into the f oot base ( U ).
17 DX-WD1202 Need help? Call 800-305-2204 Step 11: Carefully turn the unit so the fr ont is facing down, then fasten the back ( G ) to the legs ( I and J ). Use a Phillips screwd river and eight br own 7/16" large head scr ews ( II ). F asten the remaining back ( G ) to your st and using 33 nails ( KK ).
18 DX-WD1202 Need help? Call 800-305-2204 Step 12: F asten the hinges ( V ) to the doors ( H ). Use a Phillips screw driver an d eight 1/2" flat head screws ( HH ) (two for each hinge).
19 DX-WD1202 Need help? Call 800-305-2204 Step 13: Carefully turn the unit so the left end is facing down, then fast en one of the doors ( H ) t o the left end ( A ). Use a Phillips screw driver and the screw s in the hinges. Note: Y ou may need to loosen the mounting screw to slide the hi nge par t way out of the slot.
20 DX-WD1202 Need help? Call 800-305-2204 Step 14: Y ou may need to adjust the door s to make them fit correctly . T o adjust the doors from side to side (horizontal), lo osen the mounting screw sev eral turns, then turn the horizontal adjusting screw in or out.
21 DX-WD1202 Need help? Call 800-305-2204 Step 15: Apply the warnin g label ( BB ) to the top ( D ). Y ou should be able to read the label when the T V is r emoved from your stand . When the T V is in place , it should hi de the label. P eel off the back ing and ap ply the label as shown.
22 DX-WD1202 Need help? Call 800-305-2204 Still need help? F or customer ser vice, call: 800-305-2204 (U.S./C anada markets) Distributed by Best Buy P urchasing , LL C 7601 P enn Av enue South, R i chfield, MN USA 55423-3645 © 2011 BBY Soluti ons, Inc.
ww w .dynexproducts.com (800) 305-2204 Distributed by Best Buy Purchasing , LL C 7601 Penn A ve. South, Richfield, MN 55423 U .S.A. © 2011 BBY Solutions, Inc. All rights reser ved. DY NEX is a trademark of BBY Solutions, Inc. Regist ered in some countries.
An important point after buying a device Dynex DX-WD1202 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dynex DX-WD1202 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dynex DX-WD1202 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dynex DX-WD1202 you will learn all the available features of the product, as well as information on its operation. The information that you get Dynex DX-WD1202 will certainly help you make a decision on the purchase.
If you already are a holder of Dynex DX-WD1202, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dynex DX-WD1202.
However, one of the most important roles played by the user manual is to help in solving problems with Dynex DX-WD1202. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dynex DX-WD1202 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
