Instruction/ maintenance manual of the product XR-EM20 Aiwa
Go to page of 20
U XR-EM20 8C-CL7-903-01 011228ACK-H-BF For assistance and information (United States and Puerto Rico) Owner’ s record For your convenience, record the model number and serial number (you will find them on the rear of your set) in the space provided below .
2 En W ARNING To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Explanation of Graphical Symbols: The lightning flash with arrowhead symbol, within an equ.
3 En Outdoor Antenna Power lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits.
4 En Remote control Detach the battery compartment lid at the rear of the remote control and insert two R6 (size AA) batteries with correct polarity . R6(AA) • Replace the batteries with new ones when the operational distance between the remote control and main unit becomes shorter .
5 En PA RTS AND CONTROLS Main unit 4 s CLEAR CD and T ape: stops playback. Radio: clears a preset station. 5 PHONES jack Plug in optional headphones set with a stereo mini plug (ø3.5 mm). Speaker output is canceled. 6 V OLUME Adjusts the volume etc..
6 En Remote control 1 4 7 5 6 9 8 ! 0 2 3 Buttons with the same or similar names on the main unit basically have the same function. 1 PO WER 2 0–10, +10 CD: selects a track of the specified number . Radio: tunes in the station with the specified preset number .
7 En ADJUSTMENTS BEFORE OPERA TION CLOCK SET SHIFT f , g s POWER 6 ST ANDBY/ON T APE, TUNER/A UX/BAND , CD CD , TUNER/BAND , T APE,A UX, s T ONE DISPLA Y DISPLA Y f , g Setting the clock 1 Hold down SHIFT and press CLOCK on the remote control. When the unit is turned off, you can also press SET .
8 En This unit plays back finalized CD-R/RW discs as well as audio CDs. Playing a CD 1 Press OPEN to open the disc compartment. Place a disc with the label side up. Then close the disc compartment by pressing OPEN. 2 Press E to start play . To stop play Press s .
9 En Programmed play Plays back up to 30 selected tracks in programmed order . 1 Hold down SHIFT and press PROGRAM on the remote control in stop mode. " PRGM " flashes on the display . 2 Press the numbered buttons on the remote control to program a track.
10 En RADIO OPERA TIONS Manual tuning 1 Press TUNER/AUX/BAND (TUNER/BAND on the remote control) repeatedly to select a band. 2 Press f or g repeatedly to tune in a station. " TUNE " is displayed when a station is tuned in. " 1 " is displayed for FM stereo reception.
11 En SOUND ADJUSTMENTS V olume Tu rn VOLUME (press VOLUME + , - on the remote control). Adjust from 0 (minimum) to 30 and MAX (maximum). Tip : V olume level setting is retained during power -off standby. If the unit is turned off with the volume set to 17 or higher , it is automatically turned down to 16 the next time the unit is turned on.
12 En T APE PLA YBACK Playback Use only type I (normal) tapes. 1 Press z PUSH EJECT to open the cassette holder . 2 Insert the tape. Insert with the exposed side down and the side to be played facing out from the unit, and press z PUSH EJECT to close the cassette holder .
13 En To start CD recording more easily Insert the tape to be recorded, load the disc, and press SYNCHRO REC. Regardless of the function currently selected, CD play and tape recording start simultaneously . • In CD stop mode, tape recording starts from the beginning of the disc (all tracks recording).
14 En 4 Press the numbered buttons on the remote control to enter the length of the recording tape. 10 to 99 minutes can be specified. - For a 60-minute tape press 6 and 0. In a few seconds, the unit determines the tracks to be recorded for each side.
15 En Side A T ab for side A 8 Hold down SHIFT and press CD EDIT/CHECK once to switch back to side A. 9 Press REC/REC P AUSE once. The tape is rewound to the beginning of side A. " REC MUTE " flashes on the display and the lead segment is played through for 10 seconds, and recording starts.
16 En TIMER OPERA TIONS Sleep timer Tu r ns off the unit automatically after a specified time. 1 Hold down SHIFT and press SLEEP on the remote control. " 5 " and " SLP " is displayed. 2 Within 6 seconds, press f or g repeatedly to set the sleep timer duration.
17 En T imer recor ding Timer recording is available only for TUNER and AUX (with an external timer) sources. 1 Hold down SHIFT and press TIMER on the remote control repeatedly so that " 5 REC " is displayed. 2 Within 6 seconds, press SET . 3 Press f or g to set the timer-on time, and press SET .
18 En Care and maintenance Occasional care and maintenance of the unit and the software are needed to optimize the performance of your unit. To clean the cabinet Use a soft and dry cloth. If the unit surfaces are extremely dirty , use a soft cloth lightly moistened with mild detergent solution.
19 En Specifications MAIN UNIT CX-LEM20 TUNER FM tuning range 87.5 MHz to 108 MHz FM usable sensitivity (IHF) 13.2 dBf FM antenna terminal 75 ohms (unbalanced) AM tuning range 530 kHz to 1710 kHz (10 .
Printed in China NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
An important point after buying a device Aiwa XR-EM20 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Aiwa XR-EM20 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Aiwa XR-EM20 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Aiwa XR-EM20 you will learn all the available features of the product, as well as information on its operation. The information that you get Aiwa XR-EM20 will certainly help you make a decision on the purchase.
If you already are a holder of Aiwa XR-EM20, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Aiwa XR-EM20.
However, one of the most important roles played by the user manual is to help in solving problems with Aiwa XR-EM20. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Aiwa XR-EM20 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
