Instruction/ maintenance manual of the product XR-EC10 Aiwa
Go to page of 16
U XR-EC10 XR-EC12 8C-CL3-903-01 020301ASW-H-M For assistance and information (United States and Puerto Rico) Owner’ s record For your convenience, record the model number and serial number (you will find them on the rear of your set) in the space provided below .
2 En W ARNING To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Explanation of Graphical Symbols: The lightning flash with arrowhead symbol, within an equ.
3 En Outdoor Antenna Power lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits.
4 En Before starting connection, check that the protective tag has been taken off (see page 3). Connection Plug in the AC power cord to the AC outlet after all other connections are made. 1 Connect the speaker cords to the speakers. Connect the copper cords to the + terminals and the silver cords to the – terminals.
5 En PA RTS AND CONTROLS Main unit 1 4 5 6 8 3 2 7 5 VOLUME Adjusts the volume. 6 s CLEAR CD: stops playback. Radio: clears a preset station. CD E Starts and pauses play . f / r , t / g (TUNING DOWN, UP) CD: skips to a previous or a succeeding track when pressed, searches a track in fast forward or reverse playback when held down.
6 En Remote control 1 8 5 6 4 ! 9 # 0 @ 2 3 7 Buttons with the same or similar names on the main unit basically have the same function. 1 POWER 2 0–10, +10 CD: selects a track of the specified number . Radio: tunes in the station with the specified preset number .
7 En ADJUSTMENTS BEFORE OPERA TION Power Tu rning the unit on Press POWER 6 ST ANDBY/ON (POWER on the remote control). Alternatively , press TUNER/BAND, AUX, DISC DIRECT PLA Y or CD. Playback will start automatically if a disc is loaded. Tu rning the unit off Press POWER 6 ST ANDBY/ON again.
8 En This unit plays back finalized CD-R/RW discs as well as audio CDs. Playing CDs 1 Press CD1 z OPEN/CLOSE to open the disc tray . Place a disc with the label side up.
9 En Random/Repeat play In random play mode the unit plays all the tracks in random order . In repeat play mode it plays repeatedly all the discs or the track being played. Y ou can select random and r epeat a ll play at the same time. 1 Press RANDOM/REPEA T repeatedly on the remote control.
10 En RADIO OPERA TIONS Manual tuning 1 Press TUNER/BAND repeatedly to select a band. The unit switches to the radio from any other function and alternates between FM and AM. 2 Press f or g repeatedly to tune in a station. " TUNE " is displayed when a station is tuned in.
11 En Adjustments To switch to monaural FM reception Hold down SHIFT and press TUNER MODE on the remote control so that " MONO " is displayed. To cancel, r epeat the above so that “ STEREO ” is displayed. Tip : When FM stereo reception is poor , switching to monaural reduces noise.
12 En TIMER OPERA TIONS Setting the clock 1 Hold down SHIFT and press CLOCK on the remote control. When the unit is turned off, you can also press SET . 2 Within 6 seconds, press f or g to set the time. Each press changes the time in 1-minute steps. Holding these buttons down will vary the time in 10-minute units.
13 En To check the timer setting Press TIMER on the remote control so that " 5 PLAY " appears on the display . After 6 seconds, the timer -on time, the source and the timer- activated duration are displayed for 6 seconds. To change the timer setting Reset the timer again.
14 En Care and maintenance Occasional care and maintenance of the unit and the software are needed to optimize the performance of your unit. To clean the cabinet Use a soft and dry cloth. If the unit surfaces are extremely dirty , use a soft cloth lightly moistened with mild detergent solution.
15 En Specifications MAIN UNIT CX-LEC10, CX-LEC12 TUNER FM tuning range 87.5 MHz to 108 MHz FM usable sensitivity (IHF) 13.2 dBf FM antenna terminal 75 ohms (unbalanced) AM tuning range 530 kHz to 171.
Printed in Malaysia NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
An important point after buying a device Aiwa XR-EC10 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Aiwa XR-EC10 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Aiwa XR-EC10 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Aiwa XR-EC10 you will learn all the available features of the product, as well as information on its operation. The information that you get Aiwa XR-EC10 will certainly help you make a decision on the purchase.
If you already are a holder of Aiwa XR-EC10, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Aiwa XR-EC10.
However, one of the most important roles played by the user manual is to help in solving problems with Aiwa XR-EC10. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Aiwa XR-EC10 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
