Instruction/ maintenance manual of the product M1011 Dymo
Go to page of 16
Rhino M1011 www.dymo.com User Guide Guide D’Utilisation Bedienungsanleitung Guida per l’utente Guía del usuario Guia do Usuário.
2 A T ape cassette door H Charac ter selec tio n window B Ta p e r o l l e r s I Cutting handle C T ape advance knob J Embossing adjustment scr ew D Start line K Cable tie slot entrance E T ape pawl L.
3 About Y our New Label Maker W i th your new D YMO M1011 label mak er, you can cr eate metal labels . The label mak e r uses DY MO 12 mm (1/2") tape.
4 Loading the T ape The D YMO M1011 is set to emboss non-adhesive aluminium tape. T o load the tape roll 1. Hold the label maker in your lef t hand. 2. Open tape cassette door (A ). 3. I n se r t rol l of ta pe a ll ow in g t h e e nd to ex t en d a bo u t 5 cm (2 " ) t hro u gh the label sl ot.
5 Cutting the Label To c u t t h e l a b e l 1. Squeeze the embossing handle half-way , several times until the tape extends from the front of the tape exit (M) by at least 2,5 cm (1"). Before cutting the tape, make sure the end of the tape e x tends beyond the edge of the cutting asse mbly so you can easi ly pull the label out .
6 Embossing the L abel A void turning the embossing wheel at the same time y ou are squeezing the embossing handl e. This can damage the character wheel. T o emboss a label 1. T urn the character selection wheel (G) until the desired lett er is centered in the window (H).
7 Embossing on S tainless Steel Label Y ou may need to adjust the labelmak er t o emboss properly when using stainless steel tape. T o adjust for stainless steel la bel 1. T urn the adjustmen t screw (J) clockwise 3/4 t o 1 turn. 2. Emboss the t ext as described in “Embossing the Label ” on page 6.
8 Retracting the Label Y ou may want t o retract the tape, for e xample, if the tape adva nced too far or to center the text on the label. T o retrac t the label 1.
9 Removing the Label T o remov e the label 1. Retract the tape as described in “Retrac ting the Label” on page 8. 2. Open the tape cassette door (A ) and remove the label. Use caution when removi ng stainless steel tape that may hav e sharp edges.
10 Centering the T ext on the Label The trai ler length guide (N) has posi tioning marks for a short (S) or long label (L). Use the ma rks on the guide to center the text on your label. T o center the t ext on a long label 1. A fter cutting the pr evious label, emboss the text on a new la bel.
11 Applying S elf-Adhesiv e Labels Self-adhesiv e aluminum tape sticks permanently to any smooth, clean, and dry surface. T o apply self-adhesiv e tape 1. P eel off the protective backing taki ng care not to touch the adhesiv e. 2. Press the label in place.
12 Punching Holes in Non-Adhesive Labels Y ou can choose to punch one or two holes in non-ad hesive labels so tha t the labels can be attached using screws , nails, riv ets, an d metal or plastic wires or ties. Y ou can also punch a cable tie slot in one or both ends of the label.
13 Changing the Wheel Y ou can replace the character wh eel with a Reverse Image Wheel. T o change the wheel 1. Remove the tape . 2. Unscrew the screw in the center of the embossing wheel (G) and remo ve the wheel. 3. P osition the new wheel. 4. Insert t he screw in the center and tighten.
14 Hints for T rouble Free O peration Keep the following in mind when usi ng the label maker: • Letters appear where you wan t spaces - Y ou are probably squeezing the embossing handle too har d. • Letters overlap - The tape is slipping. This can happen when dir t or grease gets on the rollers.
15 Warranty Registra t ion This D YMO M1011 has been manufact ur ed under strict quality contro l and performance tested befor e leaving the factory . Within one y ear after purchase , DYMO will repai.
Distributed by/Distribué par/Distribuido por: DYMO , Atlanta, GA 30328 ©2010 Sanford, L.P . www .dymo.com Imported into Canada by/Importé au C anada par Sanford Canada L.P ., Oakville, ON L6J 3J3 En México importado y distribuido por: Newell Rubbermaid de México S.
An important point after buying a device Dymo M1011 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dymo M1011 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dymo M1011 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dymo M1011 you will learn all the available features of the product, as well as information on its operation. The information that you get Dymo M1011 will certainly help you make a decision on the purchase.
If you already are a holder of Dymo M1011, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dymo M1011.
However, one of the most important roles played by the user manual is to help in solving problems with Dymo M1011. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dymo M1011 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
