Instruction/ maintenance manual of the product M1011 Dymo
Go to page of 16
U ser Guide www .dymo.com.
2 A T ape cassette do or H Character selection window B T ape rollers I Cutting handle C T ape advance knob J Embossing adjustment screw D Start line K Cable tie slot punch E T ape pawl L Hole punch F.
3 About Y our New Labelmaker With your new DYMO M101 1 labelmaker , you can create a wide variety of plas tic and metal l abels. The labelmaker uses DYMO 12 mm (1/2") label tape.
4 Loading the Label T ape The DYMO M101 1 is set to emboss non-adhesive aluminium or plastic tape. T o load the tape roll 1. Hold the labelmaker in your left hand. 2. Open ta pe door (A). 3. Insert roll of tape allowing th e end to extend abou t 5 cm (2") through the tape slot.
5 Cutting the T ape T o cut the tape 1. Squeeze the emb ossing handle half-way , several times until the tape extends from th e front of the cutting assembly (M) by at least 1 cm (1"). Before cutting the tape, make sure the end of the tape extends beyond the edge of the cutting assembly so you can easily pull the label out.
6 Embossing th e Label Avoid turnin g the embossing wheel at the same time you are squeezing the embossing handle. This can damage the character blades. T o emboss a label 1. T urn the character selection wheel (G) until the desired letter is centered in the window (H).
7 Embossing on Stainless Ste el T ape Y ou may need to adjust the labe lmaker to emboss properly when using stainle ss steel tape. T o adjust for stainle ss steel tape 1. T urn the adjustment scre w (J) clockwise 1/2 to 3/4 turn. 2. Emboss the te xt as described in “Embossing the Label” on page 6.
8 Retracting the T ape Y ou may want to retract the tape, for exa mple, if the tape advanced too far or to center the tex t on the label. T o retract the tape 1.
9 Removing the T ape T o remove the tape 1. Retract the t ape as described in “Retracting t he T ape” on page 8. 2. Open the tape cassette door (A) and remove the tape. Use caution when removing stainless steel tape t hat may have sharp edges. 3. Reload th e tape as described in “Loading the Lab el T ape” on page 4.
10 Centering the T ext on the Label The leader/trailer lengt h guide (N) has positioning marks for a short (S) or long label (L). Use the marks on the guide to center the text on your label. T o center the tex t on a long label 1. After cutting th e previous label, emboss the text on a new label.
11 Applying Self-Adhesive Labels Self-adhesive plasti c and aluminum labels stick permanent ly to any smooth, clean, and dry surface. T o apply se lf-adhesive labels 1. Peel off the protect ive backing taking care not to touch the adhesive. 2. Press the label in place.
12 Punching Holes in Non-Adhesive Labels Y ou can choose to punch one or two holes in non-a dhesive labels so that the labels can be attached using screws, nails, rivets, and metal or plastic wires or ties. Y ou can al so punch a cable tie slot in one or both ends of the label.
13 Changing the Wheel Y ou can replace the character wheel with a Reverse Image Wheel. T o change the wheel 1. Remove the label tape. 2. Unscrew the screw in the center of the embossing wheel (G) and remove the wheel. 3. Position the new wheel. 4. Insert the screw in the center and tighten.
14 Hints for T rouble Free Operation Keep the follo wing in mind when using th e labelmaker: • Letters appear where you want spaces - Y ou are probably squeezing the embossi ng handle too hard. • Letters overlap - The tape is slipp ing. This can happen when dirt or grease gets on the rollers.
Contacting Customer Support The following table provides a list of telephone n umbers to reach DYMO Sales and Suppor t departments. Y ou can also reach DYM O at www.
W arranty Registration This DYMO M1 011 h as been manufactured und er strict quality control an d performance tested before leaving the factory. Within one year after purchase, DYMO will repair or rep.
An important point after buying a device Dymo M1011 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dymo M1011 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dymo M1011 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dymo M1011 you will learn all the available features of the product, as well as information on its operation. The information that you get Dymo M1011 will certainly help you make a decision on the purchase.
If you already are a holder of Dymo M1011, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dymo M1011.
However, one of the most important roles played by the user manual is to help in solving problems with Dymo M1011. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dymo M1011 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
