Instruction/ maintenance manual of the product Labelmaker M1011 Dymo
Go to page of 16
U ser Guide www .dymo.c om.
2 A T ape cassette door H Character selection window B T ape rollers I Cutting han dle C T ape advance knob J Embossing adjustme nt screw D Start line K Cable tie slot punch E T ape pawl L Hole punch .
3 About Y our New Labelmaker With yo ur new DY MO M101 1 labelmaker , you can c reate a wide variety of plas tic an d meta l l abels. The labelmaker uses DYMO 12 mm (1/2" ) label tape. DYMO plasti c tapes are availab le in a wide variety of colors.
4 Loading the Labe l T ape The DYMO M101 1 is set to emboss non-adhesive aluminium or plastic tape. T o load the t ape r oll 1. Hold the labelmaker in your left hand. 2. O pen t ape do or (A ). 3. Inse rt roll of tape allowing th e end to exte nd about 5 cm (2 ") through the t ape slot.
5 Cutting the T ape T o cut th e tape 1. Squeeze the emb ossin g handle half-way , several times un til the tape ext ends from th e front of the cutting assemb ly (M) by at least 1 cm (1" ). Before cutting the ta pe, make sure the end of the tape exten ds beyond the edge of the cutting assembly so you can easily pull the label ou t.
6 Embos sing th e Labe l A void turn ing the embossing wheel at the same t ime you are squeez ing the emboss ing h andle. This can da mage the character blades. T o emboss a label 1. T urn the character se lect ion wheel (G) until the desired lett er is centered in the window (H).
7 Emboss ing on Stainless Ste el T a pe Y ou may n eed t o adjust t he labelma ker to emboss properly when usin g stainle ss steel ta pe. T o adjust fo r stainless steel tape 1. T urn the adjus tment scre w (J) clock wise 1/2 t o 3/4 t urn. 2. Emboss the te xt a s describe d in “Embossi ng th e Label” on page 6.
8 Retracting the T ape Y ou may want to retract the tape, fo r exam ple, if the tape adv anced too fa r or to center the tex t on the la bel. T o retract the tape 1.
9 Removing th e T a pe T o remove the tape 1. Retract the t ape a s describe d in “Retrac ting the T ape” on page 8. 2. Open the tape cassett e door (A) and remove the tape. Use ca ution when removing stainless steel t ape that may have sha rp edges.
10 Centering t he T e xt on the Label The leader/tra iler lengt h guide (N) has position ing mark s for a short (S) or long label (L). Use th e marks on the guide to center th e text on your labe l. T o cente r the text on a lo ng label 1. After cu tting th e previous label , emboss the text on a new la bel.
11 Applying Self -Adhesive Labels Self-adhes ive plasti c and aluminum labels stick perman ently to any smooth , clean, and dry surface . T o apply self-adhe sive l abels 1. Peel of f the protect ive backing ta king care not to touch the adhes ive. 2.
12 Punching Holes in Non-Adh esive Labels Y ou can choos e to punch one or two holes in no n-adhes ive labels so that the la bels can be attached using screws, nails, rivets, and metal or plastic wires or ties. Y ou can al so punc h a cable tie slot in one or both ends of t he label.
13 Changing the Wheel Y ou can repla ce the character whee l with a Reverse Ima ge Wheel. T o change the wheel 1. Remove t he label tape. 2. Unscrew the screw in the center of the embossin g wheel (G) and remove the wheel. 3. Position the new wheel. 4.
14 Hints for T rouble Free Operation Keep t he follo wing in mind whe n using the labelmake r: • Lett ers appear where you want spaces - Y ou are probably squee zing the emboss ing handle too hard. • Letters ove rlap - The tape is slipp ing. This can happ en when dirt or grease gets on the rollers.
Contacting Customer Support The following tab le pr ovides a li st o f tele phone numbe rs to reach DYMO Sal es and Supp ort depa rtme nts. Y ou can also reach DYMO a t www .
W arran ty Registrati on This DY MO M101 1 has been m anufactu red under str ict quality cont rol and p erforman ce tested before leaving the factory .
An important point after buying a device Dymo Labelmaker M1011 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dymo Labelmaker M1011 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dymo Labelmaker M1011 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dymo Labelmaker M1011 you will learn all the available features of the product, as well as information on its operation. The information that you get Dymo Labelmaker M1011 will certainly help you make a decision on the purchase.
If you already are a holder of Dymo Labelmaker M1011, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dymo Labelmaker M1011.
However, one of the most important roles played by the user manual is to help in solving problems with Dymo Labelmaker M1011. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dymo Labelmaker M1011 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
