Instruction/ maintenance manual of the product MXD45 Dual
Go to page of 12
INSTALLATION/OWNER ’ S MANUAL AM/FM/CD Marine Receiver MXD45 MARINE.
2 MXD45 INSTALLATION Preparation Please read entire manual before installation. Before You Start • Disconnect negative battery terminal. Consult a qualified technician for instructions.
3 MXD45 INSTALLATION Wiring Diagram FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The MXD45 uses one 5 amp AGC fuse (Battery) located in-line. * CAUTION - Do not attach any speaker leads to ground as severe damage will occur.
4 MXD45 OPERATION Control Locations Release Power Volume Up/Down Audio Play/Pause Bass Boost/Mono/Stereo Tune/Track Up/Down Band Eject Mute 1 2 3 4 5 6 7 8 9 10 Auto Store/Preset Scan Display Scan Loc.
General Operation 5 MXD45 OPERATION Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure. Remove trim ring and install supplied #1 x 7/32” Phillips head scr ew thr oug h lef t sid e of mou nti ng fra me in to fa cep lat e.
6 MXD45 OPERATION General Operation Press and hold for more than 2 seconds to RESET the unit upon initial installation. The RESET button is located behind the faceplate. Refer to page 2 for details. Press AUD to select between Volume (default), Bass, Treble, Balance & Fader.
7 MXD45 OPERATION Tuner Operation Press TUNE << or >> momentarily to seek the next strong station. Press TUNE << or >> for more than 2 seconds, then release. “MANU” will momentarily appear in the display. Press TUNE << or >> momentarily to move radio frequency up or down one step at a time.
8 MXD45 OPERATION CD Player Operation With the label facing up, insert a standard size CD into the CD slot. The CD will automatically begin playback. Press EJECT to eject the CD. The unit will change to tuner mode. If the disc is not removed within 10 seconds, the unit will reload the disc.
9 MXD45 WARRANTY Limited One Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase.
10 MXD45 OPERATION Troubleshooting Problem Cause Action Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage Check connections for proper voltage (11~16VDC) Black.
11 MXD45 OPERATION Specifications Signal-to-noise: >92dB Frequency response: 10Hz-20kHz Channel separation @ 1kHz: >65dB D/A converter: 1 Bit Tuning range: 87.
www.dualav.com ©2005 Dual Electronics Corp. NSA1005-V01.
An important point after buying a device Dual MXD45 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dual MXD45 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dual MXD45 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dual MXD45 you will learn all the available features of the product, as well as information on its operation. The information that you get Dual MXD45 will certainly help you make a decision on the purchase.
If you already are a holder of Dual MXD45, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dual MXD45.
However, one of the most important roles played by the user manual is to help in solving problems with Dual MXD45. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dual MXD45 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
