Instruction/ maintenance manual of the product DB03060 Drolet
Go to page of 19
INSTRUCTIONS & OPERATIONS MANUAL DROLET COMPAK EPA EXEMPT US ENVIRONMENTAL PROTECTION AGENCY 28A CERTIFIED WOODSTOVES Verified and tested following UL 1482 Standards by: Manufactured by : STOVE BUILDER INTERNATIONAL INC. 1700, Leon-Harmel, Quebec (Quebec) G1N 4R9 Tel : ( 418 ) 527-3060 Fax : ( 418 ) 527-4311 w w w .
TABLE OF CONTENTS INTRODUCTION ............................................................................................................... 2 ASSEMBLY .................................................................................................
2 INTRODUCTION STOVE BUILDER INTERNATIONAL INC., one of the most important wood stove and fireplace manufacturers in Canada, congrat ulates you on your purchase and wishes to help you get maximum satisfaction from your w ood stove.
ASSEMBLY Legs installation: Position the stove on its back and screw the legs in place with 8 screws, 8 bolts, and 8 washers; Ash lip Installation: Screw in place with 2 bolts, 2 screws, and 2 washers.
Cast iron flue collar installation: 1. Peel off the tape from the back of the gasket and attach the gasket to the rope groove at the back of the flue collar; 2. Mount flue collar on top of the stove. Make sure that the damper holes on each side of the flue collar are parallel to the back of the stove; 3.
5 INSTALLATION SAFETY NOTICE • I F THIS STOVE IS NOT PROPERLY INSTALLED , A HOUSE FIRE MAY RESULT . T O REDUCE THE RISK OF FIRE , FOLLOW THE INSTALLATION INSTRUCTIONS . F AILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE , BODILY INJURY , OR EVEN DEATH .
CLEARANCES FROM COMBUSTIBLES It is of outmost importance t hat the clearances to combusti ble materials be scrupulously respected upon installation of the stove you hav e selected.
7 CHIMNEY Your wood stove may be hooked up with a factory built or masonry chimney. If you are using a factory built chimney, it must comply with UL 103 standards; t herefore it must be a Type HT (2100°F). It is extremely important that it be install ed according to the manufacturer's specifications.
CHIMNEY CONNECTOR (STOVE PIPE) The stove pipe must be made of aluminized or cold roll steel with a minimum thickness of 0.021" or 0.53 mm. It is strictly forbidden to use galvanized steel. Your smoke pipe should be assembled in such a way that the male section of the pipe faces down.
TYPICAL INSTALLATIONS FACTORY BUILT CHIMNEY: ROOF FLASHING 18" CLEARANCE WALL SUPPORT WALL RADIATION SHIELD RAIN CAP Wall installation CEILING SUPPORT RADIATION SHIEL D Vertical installation 9.
MASONRY CHIMNEY: Cl ay l i n er Thim b l e C l ea n out door 10.
FACTORY BUILT THIMBLE: 11.
BRICK THIMBLE: 12.
13 WOOD STOVE UTILISATION Your heating unit was designed to burn wood onl y; no other materials should be burnt. Wastes and other flammable materials should not be burnt in your wood stove. Any type of wood may be used in your stove, but spec ific varieties have better energy yields than others.
14 Smaller pieces of wood will dry faster. All l ogs exceeding 6" in diameter should be split. The wood should not be stored directly on the ground. Air should circulate through the cord. A 24" to 48" air space should be left between each row of logs, which should be placed in the sunniest location possible.
15 ASH DISPOSAL Ashes should be removed from the stove ever y few days or when ashes get to 2 to 3 inches deep. Always empty the stove when it is cold, such as in the morning.
16 AIR CIRCULATION SYSTEM In order to improve air circul ation in the room where the wood stove is installed, certain options are available for specific stove models.
17 WARNING: • N EVERS OPERATE THE STOVE WITHOUT A GASKET OR WITH A BROKEN ONE . D AMAGE TO THE STOVE OR EVEN HOUSE FIRE MAY RESULT PAINT Only clean your stove with a dry soft clothe that will not harm the paint finish.
18 DROLET LIMITED LIFETIME WARRANTY The warranty of the manufacturer extends only to the original consumer purchaser and is not transferabl e. This warranty covers brand new products only, whic h have not been altered, m odified nor repaired since shipm ent from factory.
An important point after buying a device Drolet DB03060 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Drolet DB03060 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Drolet DB03060 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Drolet DB03060 you will learn all the available features of the product, as well as information on its operation. The information that you get Drolet DB03060 will certainly help you make a decision on the purchase.
If you already are a holder of Drolet DB03060, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Drolet DB03060.
However, one of the most important roles played by the user manual is to help in solving problems with Drolet DB03060. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Drolet DB03060 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
