Instruction/ maintenance manual of the product NDR1062 Dometic
Go to page of 20
INST ALLA TION AND OPERATING INSTRUCTIONS REFRIGERA TOR FOR LP-GAS AND ELECTRIC OPERA TION NDR1062 USA Corporate Office CANADA Service Office 2320 Industrial Parkway Elkhart, IN 46515 Dometic Distribution Inc. Dometic Corporation 866 Langs Drive 2320 Industrial Pkwy .
.
3 FIG. 2 Refrigerator control p anel ON OFF AC GAS AU TO CHECK COLD 1 2 3 4 5 COLDEST B AD C 2 1 E 3 F G LEGEND 2-W A Y AMES Model 1. Main Power Button ON/OFF 2. AUTO/GAS Mode Selector Button 3. T emperature Selector Button A. AUTO Mode Indicator Lamp B.
4 INST ALLA TION GENERAL INSTRUCTION This appliance is designed for storage of foods and storage of frozen foods and making ice. This appliance is certified under the latest edition of ANSI Z21.
5 12 V olt s DC Connection This refrigerator model require a continuous 12 volt DC supply to maintain the automatic energy system. The connection is made to the positive (+) and negative (-) terminals located at the rear of the refrigerator . (See FIG .
6 2. Once the lower front strip is slipped under the hinge, the part is possible to swing into place as shown in FIG . 6. 3. Secure the refrigerator and the lower front strip with two screws: One screw through the hinge, and on the opposite side one screw through the lower front strip.
7 CERTIFIED INST ALLA TION Certified installations require one roof vent and one lower side vent. For “Certified V ent System Kit s” see p age 16 .
8 OPERA TING INSTRUCTIONS IMPORT ANCE OF LEVELING A REFRIGERATOR In an absorption refrigerator system, ammonia is lique- fied in the finned condenser coil at the top rear of the refrigerator.
9 THERMOST A T The thermostat on the refrigerator controls both the gas and electric operation, thereby eliminating the necessity of resetting each time a different energy source is em- ployed. After the initial start-up, the thermost at should be moved from “COLDEST” to the desired temperature setting, usually at mid setting.
10 DESCRIPTION OF OPERA TING MODES AUTO MODE When operating in the AUTO mode, the AUT O mode indicator lamp (A) will illuminate. The control system will automatically select between AC and GAS operation with AC having priority over GAS.
11 ! WARNING When all the frost has melted, dry the interior of the re- frigerator with a clean cloth. Replace all food and set the thermostat to the COLDEST temperature setting for a few hours. Then reset the thermostat to the desired set- ting, usually at mid setting.
12 ELECTRIC EQUIPMENT HEA TER The heat necessary for the operation of an absorption cooling unit is supplied by an electric heater mounted in a pocket of the boiler system. This model is equipped with one electric heater for 120 volt AC. To replace the heater proceed as follows: 1.
13 B . Check all connections in the LP gas system (at the back of the refrigerator) for gas leaks. The LP gas supply must be turned on. Apply a non-corrosive bubble solution to all LP gas connections.
14 TROUBLESHOOTING The Refrigerator Does Not Cool Properly A. Burner jet clogged. Clean. (See Section Maintenance & Service, item 2. Periodic maintenance, Paragraph E item 1-13. B. Check level of refrigerator. C. Venting problem. Restriction in air flow across cooling unit.
15 1 1 1 2 1 1 1 3 3 4 5 P ANEL DIMENSIONS MAX. THICKNESS 5/32" (4 mm) REFR. MODEL HEIGHT WIDTH TYPE MAX. MIN. MAX. MIN. NDR1062 upper m m 403 401 527 524 inch 15-27/32 15-25/32 20-3/4 20-5/8 low.
16 CERTIFIED VENT SYSTEM KITS REFRIGERATOR KIT MODEL NO. COMPONENTS PART NO. NDR1062 4A Roof Base 3103633.XXX* Roof Cover 3103634.XXX* Lower Side V ent 3109350.XXX* * Fill in “XXX” with color code numbers. For color codes, contact your supplier. For further information contact your dealer or distributor.
17 Put a screwdriver into the slot of the shelf lock. Turn the screwdriver counterclockwise. Remove the shelf locks from the wire shelf. Insert the ends of the wire shelf on the left-hand side at the desired position. Slide the wire shelf to the left.
18 NDR1062.
19.
20 MO-FO 0445.
An important point after buying a device Dometic NDR1062 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dometic NDR1062 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dometic NDR1062 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dometic NDR1062 you will learn all the available features of the product, as well as information on its operation. The information that you get Dometic NDR1062 will certainly help you make a decision on the purchase.
If you already are a holder of Dometic NDR1062, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dometic NDR1062.
However, one of the most important roles played by the user manual is to help in solving problems with Dometic NDR1062. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dometic NDR1062 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
