Instruction/ maintenance manual of the product XR6 DMP Electronics
Go to page of 28
Users Guide XR6/XR10.
Copyright © 1995 - 1999 Digital Monitoring Products, Inc. Information furnished by DMP is believed to be accurate and reliable. This information is subject to change without notice. Silencing an Alarm All/Perimeter and Home/Away Systems 1. While the alarm bell or siren is sounding, enter your user code.
About your system Emergency Ev acuation Plans ....................................... i i About Y our Security System .......................................... 1 The Security Command K eypad ................................... 2 Special Security Command Messages .
Emergency Ev acuation Plans The National Fire Protection Association recommends that you establish an emergency evacuation plan to safeguard lives in the event of a fire or other emergency. Use the following steps as a guide. Draw a floorplan of your home or business On a clean sheet of paper, draw the walls, windows, doors, and stairs.
1 About Y our Security System Your Security Command system has been designed with your safety and comfort in mind. It uses the latest in computer technology to create the most user friendly security and fire system on the market today.
2 Data Entry keys These keys allow you to enter your user code when arming or disarming or enter other information into the system. The ARROW key The ARROW key is used to go back through the keypad displays while operating your system.
3 INVALID CODE The code number you've entered a second time is considered invalid by the system. SYSTEM TROUBLE or SERVICE REQUIRED There is an electronic failure in your system.
4 Understanding Security System T erms Throughout this guide, and in some displays on your keypad, you’ll see certain words or phrases that might be unfamiliar. Although every effort has been made to use terms that are commonly known, there are some for which there was no acceptable substitute.
5 Status List The keypad Status List displays any alarm or trouble condition on a zone and any trouble condition that occurs with the AC power or battery power. If more than one alarm or trouble condition occurs at the same time, the keypad sequences this information on its display.
6 Ho w your System Operates Your system has been programmed to operate in one of two modes: All/Perimeter, or Home/Away. • All/Perimeter - In this mode you select All to turn on the entire system or Perimeter to turn on just the exterior door and window protection when you're inside.
7 All/P erimeter System Arming Area Assignment: Your security system is divided into two separate areas. Motion detectors, inside doors, and other interior protection devices are assigned to the Interior area while windows and exterior doors are assigned to the Perimeter area.
8 All/P erimeter System Disarming Disarming: While the system is armed, you can only enter the premises through an entry/exit delay door without causing an alarm. After opening the door, the Security Command keypad sounds a prewarn tone to remind you to disarm the system.
9 Home/A wa y System Arming Area Assignment: Your security system is divided into two or three separate areas. Motion detectors, inside doors, and other interior devices are assigned to an Interior and possibly Bedroom area while windows and exterior doors, are assigned to a Perimeter area.
10 Home/A wa y System Disarming Disarming: While the system is armed, you can only enter the premises through an entry/exit delay door without causing an alarm. After opening the door, the Security Command keypad sounds a prewarn tone to remind you to disarm the system.
11 Security Command User Menu Many of the features of your system have been put into a User Menu you can access from any Security Command keypad. The menu requires you to enter your user code and then only shows those functions to which you have access.
12 Outputs On Off User Code Level : Master or Standard. Function : Allows you to turn the system's outputs on and off. This function is used to individually turn your system’s relay outputs on and off. Your system may use these outputs to control interior and exterior lighting, or heating, air conditioning, or other appliances.
13 User Menu Zone Monitor User Code Level : Master and Standard. Function : Allows the system to monitor selected disarmed zones (doors, windows, or motion detectors) and sound a tone at the keypad as well as display their name on the keypad display as they're faulted.
14 User Codes User Code Level : Master only. Function : Allows you to add or delete a user from the system or change their security code or authority level. There are three characteristics associated with each user code that define its capabilities within the system.
15 User Codes continued User Code Authority Levels System Options Standard Master Sensor Reset ✔✔ Outputs On/Off ✔✔ Zone Monitor ✔✔ System Test ✔✔ Arm and Disarm ✔✔ Display Events ✔✔ User Codes ✔ Adding User Code Numbers: 1. Access the User Menu.
16 User Codes continued Deleting User Code Numbers: 1. Access the User Menu. 2. Press the COMMAND key until USER CODES? displays. 3. Press any one of the SELECT keys. The keypad displays ADD DEL CHG . 4. Press the SELECT key under DEL to delete a user code from the system.
The event display you'll see at the keypad is slightly different for each event type. Using the Display Events Function 1. Access the User Menu. 2. Press the COMMAND key until DISPLAY EVENTS? displays. Press any SELECT key. 3. The keypad displays the oldest recorded event.
18 User Menu Zone Event Displays This section displays alarms, troubles, and other events that could occur on your system's protection zones. Display Description JONES RESIDENCE A burglary alarm occurred on zone 2. 2 BURG ALR Press the SELECT key under the zone number to display the custom zone name programmed into the system.
19 User Code Change Event Displays This displays any addition, deletion, or change to a user code. Display Description JONES RESIDENCE User 9 added user 12 to the system.
20 System Setup System Setup We've provided this System Setup section to allow you to track the current and future status of the programmable options on your Security Command system. If you make changes to the system, you should update the information contained on these pages.
21 P ager Direct™ User's Guide Pager Direct uses the reporting capability of your security system to dial your pager number and send reports in much the same way as someone sending you a pager message would do. You can receive reports of alarms, troubles, or armings and disarmings of the system and know at a glance the status of your system.
22 Account Number Security Command Numeric Paging Numeric Pager Display This number has been programmed into your Security Command system as an identifier . Whenever the system sends a message to your pager , it will always send the account n umber first to identify itself.
23 Notes:.
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282 LT-0226 (4/99) Digital Monitoring Products.
An important point after buying a device DMP Electronics XR6 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought DMP Electronics XR6 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data DMP Electronics XR6 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, DMP Electronics XR6 you will learn all the available features of the product, as well as information on its operation. The information that you get DMP Electronics XR6 will certainly help you make a decision on the purchase.
If you already are a holder of DMP Electronics XR6, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime DMP Electronics XR6.
However, one of the most important roles played by the user manual is to help in solving problems with DMP Electronics XR6. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device DMP Electronics XR6 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
