Instruction/ maintenance manual of the product ZTR 5017Twin Dixon
Go to page of 48
1 Page 5000 SERIES ZTR ® MOWERS Operator's Manual 2001.
Page 2 IMPOR T ANT - READ CAREFULL Y The Dixon ZTR M o wer is both easy and fun to operate. H ow ever , any power mow er must be operated properly to be safe. It is not a to y or a recr eational vehicle. Befor e you start to use the mower , read the operator's manual car efully and become completely familiar with the controls.
3 Page INDEX SAFETY .................................................................. P ages 4- 9 W ARRANT Y POLICY ............................................ P age 10 SPECIFICA TIONS ................................................. P age 11-13 SEA T ADJUSTMENT .
Page 4 ...read and understand this manual to prevent injuries. TIP-OVER BACK-OVER RUN-OVER BLADE CONTACT SAFET Y RIDING L A WNMO WERS, IF IMPROPERL Y OPERA TED, CAN CA USE SERIOUS INJUR Y OR DEA TH The most common causes of injur y to the operator or bystander .
5 Page SAFET Y SAFETY SYM BOLS Safety Alert Symbol When you see this symbol, BE ALER T to the potential for injury . F ollow r ecommended safety pr ecautions and safe operating practices. Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Page 6 GENERAL OPERA TION: • Read, understand, and follow all instructions in the manual and on the mower before starting. • Only allow responsible adults, who are familiar with the instructions, to operate the mower. • Clear the area of objects such as rocks, toys, wire, etc.
7 Page SAFET Y SL OPE OP ERA TION: Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in sev ere injur y or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it! DO Mow across the slope with your Dixon ZTR - never up or down.
Page 8 SAFET Y CHILDREN: T ragic accidents can occur if the operator is not alert to the presence of children. Children are attracted to lawn mowers and the mowing activity. NEVER assume children will stay where they were last seen. Be alert to avoid accidents.
9 Page SAFET Y SER VICE: • Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. Use only an approved container. Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling.
Page 10 DIXON INDUSTRIES, INC. a BLOUNT company AIRPORT INDUSTRIAL PARK PO BOX 1569 COFFEYVILLE KS 67337 0945 316 251 2000 FAX 316 251 4117 DIXON LIMITED WARRANTY POLICY - COMMERCIAL MODELS Models 6000 & 7000 WARRANTY: Home Owner Application: This Dixon Warranty term is for a period of two (2) years from date of purchase.
11 Page SP ECIFICA TIONS M odel ZTR 5020 CHASSIS: 11 GA - rectangular tube BODY: Two piece - made of rotational molded polyethylene. Front body contains access panels for battery service and engine to mower deck belt removal. Rear body tilts up to allow service on the entire drive system.
Page 12 CHASSIS: 11 GA - rectangular tube BODY: Two piece - made of high-density polyethylene. Front body contains access panels for battery service and engine to mower deck belt removal. Rear body tilts up to allow service on the entire drive system.
13 Page SP ECIFICA TIONS M odel ZTR 5017T win CHASSIS: 11 GA - rectangular tube BODY: Two piece - made of rotational molded polyethylene. Front body contains access panels for battery service and engine to mower deck belt removal. Rear body tilts up to allow service on the entire drive system.
Page 14 SEA T ADJUSTMENT INSTR UCTIONS 5000 Series 1. G rasp seat slide adjuster and move it into adjustment position. 2. S lide seat for ward or backwar d.
15 Page CONTR OLS.
Page 16 The parking brake is designed to hold the mower from moving and is not intended for use in stopping the mower while it is in motion. . T O SET P ARKING BRAKE: The hand operated parking brake is located at left hand side of mower. To engage brake, pull lever up (to the rear).
17 Page CONTR OLS T O GO FOR W ARD: From neutral position, gently push both drive levers forward. To increase speed, move levers farther forward. T O GO BACKW ARD: From neutral position, gently pull both drive levers toward you. TURNING: Turning is controlled by moving one drive lever slightly forward or rearward of the other.
Page 18 CONTR OLS BLADE DRIVE: Located on control panel, on operator's right. To engage blades: Pull up on the switch. To disengage blades: Push down. CIR CUIT BREAKER: Located on control panel, on operator's right. Protection of the electrical system is by (1) 15 amp circuit breaker.
19 Page OP ERA TION INSTR UCTIONS Safe and successful operation will depend upon the operator having the correct knowledge of all controls used on the mower and making good judgements about the terrain to be mowed. NEVER allow anyone to operate the mower without complete knowledge of all controls and their functions.
Page 20 P ARKING BRAKE SWIT CH TEST : a) Place P arking Brake in OFF position b) T ur n ignition switch to ST AR T E NGINE SHOULD NO T TURN O VER OR A TTEMPT TO ST AR T ! BLADE DRIVE SWIT CH TEST : a).
21 Page OP ERA TION INSTR UCTIONS ST AR TING INSTR UCTIONS: Cold Engine 1. Position choke control in ON position. 2. Position throttle control at 1/2 speed setting. 3. Insert ignition key and turn to "Start" position. When engine starts, release ignition key.
Page 22 OP ERA TION INSTR UCTIONS MO WING WITH A MUL CHING A T T A CHMENT : Mulching or recycling the grass clippings requires a totally different mowing approach than would be normal when side discharging or bagging the grass. There may be instances or conditions where it is not possible to hide all of the recycled or mulched clippings.
23 Page OP ERA TION INSTR UCTIONS MO WING WITH A GRASS CA T CHER A TT A CHMENT : In order to achieve optimum performance when mowing with a grass catching attachment, please read and follow the tips listed below: 1. Set engine speed control to the wide open or full setting.
Page 24 OP ERA TION INSTR UCTIONS CAUTION GRASS HEIGHT SUGGESTIONS : Correct mowing height can reduce weeds and disease by 50% to 80% The following grass cut heights are based on adequate moisture conditions and normal thatch buildup in a healthy lawn.
25 Page OP ERA TION INSTR UCTIONS DECK ROLLERS : 60" Deck Purpose: The spring loaded deck rollers located at the front corners of the 60" mower deck are designed as an aid to limit turf scalping when mowing on uneven ground. Height: Normal height settings as installed at the factory allows each roller to ride slightly above the turf.
Page 26 CARE AND MAINTENANCE This portion of the owner's manual deals with normal service items which can be performed by the owner. Please remember that if you are in doubt as to the correct ser.
27 Page CARE AND MAINTENANCE MO WER BL ADE MAINTENANCE : NOTE: Observe proper blade position prior to removal. 1. Safely raise front of mower. 2. Hold or block blade from turning. 3. Loosen blade nut and remove blade. 4. When replacing blade, tighten blade nut securely.
Page 28 REAR HANGER PIN BEL T TENSION ENGINE T O MO WER DECK BEL T : 42" and 50" P/N 6111 60" P/N 6938 The engine to mower deck drive belts are automatically held in proper tension by springs which push the deck assembly forward and do not require any additional adjustment to be made.
29 Page CARE AND MAINTENANCE FUEL SHUT OFF V AL VE: A fuel shut off valve is located at the bottom rear of each fuel tank. Always turn the valve to the "OFF" position when the mower is stored or not in use.
Page 30 CARE AND MAINTENANCE REAR WHEELS: The rear wheels of all 5000 Series models are of an "offset" center design to allow "reversed" installation for using snow chains or to gain increased stability when mowing on sloped ground.
31 Page CARE AND MAINTENANCE HOT oil may cause burns. Allow engine to cool before draining oil. CHANGING THE ENGINE OIL: 1. The "Dapco" oil drain valve is located on the left side of the engine crankcase. 2. Place a suitable container under the drain valve.
Page 32 CARE AND MAINTENANCE MO WER DECK REMO V AL : 1. Remove mower deck drive belt. To relieve belt tension, insert 5283 link (at front of lift frame) into tab illustrated below. Move lift handle into the lowest cut position. Belt can now be removed from mower deck pulley.
33 Page MO WER DECK LEVELING PROCEDURE: There are a total of (4) threaded adjusters which will control the attitude or pitch of the mower deck. The adjusters have lock nuts on the bottom which can be turned up or down to raise or lower the front and rear of the mower deck.
Page 34 CARE AND MAINTENANCE Adjustment of the drive system is limited to the actual function of the hydrostatic transmissions as outlined below. T -BO X T O HYDROST A T BEL T ADJUSTMENT : Tighten the.
35 Page CARE AND MAINTENANCE NOTE: Cable must have the recommended 1-1/2 to 2 inches of free play with parking brake released or drive belt may slip, causing loss of power. P ARKING BRAKE CABLE ADJUSTMENT : Make necessary adjustments to the T-Box to Hydrostat belt, as shown on page 34.
Page 36 CARE AND MAINTENANCE NEUTRAL ADJUSTMENT : CONTROL TUBE BOLT LOOSEN IN STEP A TIGHTEN IN STEP E JAM NUTS LOOSEN IN STEP B TIGHTEN IN STEP D 9067 CONTROL ROD ADJUST IN STEP C 5540 CONTROL TUBE 4. Engage parking brake and lower the body. Release parking brake and swing control levers in.
37 Page CARE AND MAINTENANCE FOR W ARD TRA VEL SPEED ADJUSTMENT : 1. Drive machine on a smooth, level surface with both levers in top speed position. 2. If one side drives slightly faster than the other, adjust forward speed bolt in to contact stop sooner.
Page 38 CARE AND MAINTENANCE PROCEDURE FOR ELECTRIC CL UT CH ADJUSTMENT Electric clutches require periodic Air Gap adjustments for extended life. Listed below is both an Air Gap adjustment procedure and an Ohms test to check for a faulty coil within the clutch.
39 Page CARE AND MAINTENANCE HYDROST A TIC TRANSMISSION OIL AND FIL TER SER VICE SERVICE INTERVALS: 1. Initial filter service - 50 hours. 2. Every 250 hours or once a year thereafter. OIL REQUIREMENTS: Any high quality engine oil with an API classification of SG/CD is recommended.
Page 40 CARE AND MAINTENANCE HYDROST A TIC TRANSMISSION OIL & FIL TER SERVICE If transmission is to be serviced, proper air purging procedures must be followed, or damage will occur. Proceed as follows: 1. Remove oil filter from chassis, allowing oil to drain into container.
41 Page CARE AND MAINTENANCE WHEELS AND TIRES: Correct tire pressure is important for correct operation of mower. Front Tires 11 x 4 x 5 16-21 lbs. Rear Tires(5020&5023) 20 x 10.5 x 8 8-14 lbs. Rear Tire (5425) 18 x 9.5 x 8 8-14 lbs. NOTE: Check lug nuts periodically for tightness.
Page 42 ST ANDARD SER VICE P AR T S LIST 42" DECK BLADES: Lo Lift P/N 6236 S tandard Hi-Lift P/N 8688 BEL TS: Engine to M ower Deck P/N 6111 Serpentine Belt P/N 6109 Engine to T -Box P/N 7253 T -.
43 Page ST ANDARD SER VICE P AR T S LIST K OHLER AND BRIGGS & STRA T T ON AIR AND OIL FIL TER P AR T NUMBERS: Refer to engine manufacturers manual for recommendations regarding frequency of service required for engine oil changes and air filter maintenance.
Page 44 SITUATION CAUSES REMEDY Poor cut quality Ground speed Reduce mowing speed. Poor cut quality Incorrect engine to Refer to page 42 for part numbers. mower deck belt Poor cut quality Engine RPM too low Increase engine RPM to maximum. Poor cut quality Dull or bent blade Sharpen or replace as required.
45 Page SITUATION CAUSES REMEDY Mower pulls to one Forward travel Refer to page 37 for procedure side or the other speed adjustment or consult your dealer for repair. TR OUBLESHOO TING DRIVE SYSTEM: Incorrect oil filter installed on system. Hydrostatic transmissions are "air locked", low or no oil return to tank.
Page 46 ELECTRICAL SYSTEM: SITUATION CAUSES REMEDY Starter will not Circuit breaker Push button to reset turn en gine over disengaged Consult your dealer for repair Starter will not Dead battery Charg.
47 Page DIXON INDUSTRIES, INC. A BLOUNT International Inc. Co. PO BOX 1569 COFFEYVILLE KS 67337 0945 316 251 2000 FAX 316 251 4117 Address DATE PURCHASED MOWER MODEL NUMBER Name DATE OIL CHANGED: DATE.
Page 48 Dixon ® and ZTR ® are registered trademarks of Dixon Industries, Inc. 5000Series 5020,5023&5425 Part No. 13089-0600 DIXON INDUSTRIES, INC.
An important point after buying a device Dixon ZTR 5017Twin (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dixon ZTR 5017Twin yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dixon ZTR 5017Twin - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dixon ZTR 5017Twin you will learn all the available features of the product, as well as information on its operation. The information that you get Dixon ZTR 5017Twin will certainly help you make a decision on the purchase.
If you already are a holder of Dixon ZTR 5017Twin, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dixon ZTR 5017Twin.
However, one of the most important roles played by the user manual is to help in solving problems with Dixon ZTR 5017Twin. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dixon ZTR 5017Twin along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
