Instruction/ maintenance manual of the product DFI2309 Dimplex
Go to page of 19
Service Manual 23” Insert Model Numbers: DFI2309 MOD ~ to D DFI2310 MOD ~ to D 7400070000rev01 In keeping with our policy of continuous product development, we reserve the right to make changes without notice. Dimplex North America Limited 1367 Industrial Road Cambridge ON Canada N1R 7G8 1-888-346-7539 www .
2 T able Of Contents Operation ...................................................... Page 3 E x p l o d e d P a r t s D i a g r a m .......................................... Page 5 Replacement Parts List . . . . . . . . . . . . . . . . . . . . . . .
3 Operation Electric Fireplace Manual Control The manual controls for the unit are located in the top, right corner , on the front of the rebox (Figure 1). A switch is in the On position when the side with the “ I ”, or “ II ” markings on it is pushed in.
4 Figure 3 On Button Off Button Battery Cover Battery The remote control has a range of approximately 50 feet (15.25 m). It does not have to be pointed at the replace and can pass through most obstacles (including walls).
5 Exploded Parts Diagram 6 1 2 3 4 5 11 12 8 9 16 10 13 14 15 7.
6 Replacement Parts List DFI2309 - Part Number ..................6 9 0 1 4 7 0 1 5 9 DFI2310 - Part Number ..................6 9 0 1 4 7 0 2 5 9 Replacement Parts for both DFI2309, DFI2310 all MODs: 1. Cord set . . . . . . . . . . . . . . . . . . . . .
7 Wiring Diagram - DFI2309 MOD ~ to B Flicker Motor Lamp holders Blower Cutout Cord Set T erminal Block Main On/Off Switch Low Heat Switch High Heat Switch Heater Elements T erminal Block.
8 Wiring Diagram - DFI2309 MOD C to D Remote Receiver Board Blower Flicker Motor Lamp holders Cutout Cord Set T erminal Block Main On/Off/On Switch Low Heat Switch High Heat Switch Heater Elements T e.
9 Wiring Diagram - DFI2310 MOD ~ Blower Flicker Motor Lamp holders Cutout Cord Set T erminal Block Main On/Off Switch Low Heat Switch High Heat Switch Heater Elements T erminal Block LED Log Set Drive.
10 Wiring Diagram - DFI2310 MOD A to D Blower Flicker Motor Lamp holders Cutout Cord Set T erminal Block Main On/Off/On Switch Low Heat Switch High Heat Switch Heater Elements T erminal Block LED Log .
11 Mirror Replacement If the rebox was operating prior to servicing allow at least ve (5) minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
12 a small Phillips screwdriver to loosen the screw which clamps the wire from the cutout to the terminal block. ii) With wires loose from their connections, remove the small Phillips screw that attaches the cutout to the heater assembly (Figure 8). Remove and discard old cutout.
13 Power Cord Replacement If the rebox was operating prior to servicing allow at least ve (5) minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
14 Light Bulb Replacement Allow at least ve (5) minutes for light bulbs to cool before touching bulbs to avoid accidental burning of skin. Light bulbs need to be replaced when you notice a dark section of the ame. There are two (2) bulbs under the log set which generate the ames and embers .
15 2. Carefully remove the Log Set from the rebox. 3. Disconnect LED harness to Log Set ( DFI2310 only ). Set Log Set aside (Figure 12). 4. Pull Flicker Rod to the far right, towards the Flicker Motor , carefully bend the Flicker Rod enough to release the opposite end from the mounting bracket (Figure 12).
16 opposite end from the mounting bracket (Figure 12). 5. Pull Flicker Rod off of the shaft of the Flicker Motor and set aside. 6. T urn rebox onto its back and remove the four (4) Phillips screws as shown in Figure 15. 9. Using a small Phillips screwdriver , loosen all three (3) of the left side terminals of the T erminal Block.
17 6. The Remote Receiver Board is located on the side panel just above the entry point for the power cord (Figure 18). Figure 18 7. Either pinch the clasp to release or cut each of the four (4) mounting studs (one in each corner of the Receiver Board) that attach the circuit board to the chassis of the rebox.
18 rear of the light assembly (Figure 19). 14. Remove light sockets by placing a hand inside light assembly , grasping light socket and pulling light socket until it snaps out of place. 15. Feed wires of replacement light sockets through holes in sheet metal, properly orientate and push light sockets in until they snap into place.
19 7. Either pinch the clasp to release or cut each of the four (4) mounting studs (one in each corner of the Log Driver Board) that attach the circuit board to the chassis of the rebox. ! NOTE: If mounting studs are cut, ensure they are replaced by those supplied with replacement board.
An important point after buying a device Dimplex Dimplex DFI2309 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dimplex Dimplex DFI2309 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dimplex Dimplex DFI2309 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dimplex Dimplex DFI2309 you will learn all the available features of the product, as well as information on its operation. The information that you get Dimplex Dimplex DFI2309 will certainly help you make a decision on the purchase.
If you already are a holder of Dimplex Dimplex DFI2309, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dimplex Dimplex DFI2309.
However, one of the most important roles played by the user manual is to help in solving problems with Dimplex Dimplex DFI2309. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dimplex Dimplex DFI2309 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
