Instruction/ maintenance manual of the product IP-200PHD-24 AirLive
Go to page of 97
i IP-200PHD-24 / IP-200PHD-24B 2.0 Mega Pixel Passive PoE IPCamera User’s Manual.
Copyright & Disclaimer i AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Copyright & Disclaimer No part of this publication may be reproduced in any form or by any means, whether electronic, mechanical, photocopying, or recor ding without the written consent of OvisLink Corp.
Copyright & Disclaimer AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual ii FCC Statement Federal Communication Commission Interf erence Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Table of Contents iii AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Table of Contents 1. Introduc tion ..................................................................................................... 1 1.1 Overview..
Table of Contents AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual iv 4.2.3 PPPoE ....................................................................................... 29 4.2.4 Steamin g .......................................................
1. Introduction 1 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 1 1. Introduction 1.1 Overview This camera is an inexpensive and fully scalable surveillance device.
1. Introduction AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 2 1.2 Features z Easy installation with setup wizard (IP Wizard II) z UPnP device discovery and NAT router transversal for easy installation z Dynamic IP Service, DIPS®, to search your IP camera from Internet easily z H.
1. Introduction 3 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 1.4 Package Contents User can find the following items in the package: z This camera is the main element of the product. z Camera Stand with screws z Power adapter dedicates 12V DC electric power output to Network Camera.
1. Introduction AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 4 1.5 Physical Description 1.5.1 Front View z IP-200PHD-24 1. Lens & Focus Ring User could use this ring to adjust focus manually. 2. Microphone The Camera has built-in an internal microphone.
1. Introduction 5 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 1. Lens & Focus Ring User could use this ring to adjust focus manually. 2. Microphone The Camera has built-in an internal microphone. This microphone is hidden in the pinhole located on the front panel.
1. Introduction AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 6 3. Factory Default Reset This button is hidden in the pinhole. Th is button is used to restore the all factory default settings. Sometimes re starting the camera will make the system back to a normal stat e.
1. Introduction 7 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 3. Plug an Ethernet cable into the Camera Connect an Ethernet cable to the LAN socket located on the Network Camera’s bottom and attach it to the network. 4.
1. Introduction AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 8 Note : Use the power adapter, 12VDC, included in the package and connect it to wall outlet for AC power.
2. Getting Started 9 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 2 2. Getting Started 2.1 IP Wizard Once you have installed the Network Camera well and powered it on, the network accessing type LED will turn on. It means the system is booting up successfully.
2. Getting Started AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 10 When launch the IPWizard II, a searching window will pop up. IPWizard II is starting to search Network Cameras on the LAN.
2. Getting Started 11 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 2.2 View If IPWizard II finds network devices, View button will be available. Please select the device you want to view and click the View button. Then you could see the video from camera directly.
2. Getting Started AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 12 You could modify the relative setti ngs of the selected device. Click “ << ” button will quit the LAN setting procedure and click “ >> ” button will move to next page as below.
2. Getting Started 13 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual In case, you do not want to change user name and/or password, then just click “ Submit ” button to perform your se tting accordingly. Click “ << ” button will go back to previous page.
2. Getting Started AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 14 To discover your device, go to your Desktop and click My Network Places . Click the targeted Device. Then Internet Explorer will connect to this Network Camera automatically.
2. Getting Started 15 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual (1) Enable UPnP option of your NAT router To use UPnP IGD function (NAT traversal), you need to make sure the UPnP function is enabled in your router. Most new home routers should support this function.
2. Getting Started AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 16 2. Type in your login name and password under “USERNAME” and “PASSWORD” textbox.
2. Getting Started 17 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 2.6.2 Login as Administrator If you log in the Camera as the Administrator, you can perform all the settings provided by the device. Start-up screen will be as follow no matter an ordinary users or an administrator.
3. Configure the Camera AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 18 3 3. Configure the Camera 3.1 Monitor the Image Section The image shot by the device is shown here. The date and time are displayed at the top of the window. 3.2 View Profile The device supports multi-profile function for H.
3. Configure the Camera 19 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual : Disable audio up loading function. : Enable audio uploading function. 3.6 Full Screen Enlarge video to full screen display. : Enlarge video to full screen disp lay.
3. Configure the Camera AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 20 3.7.1 Digital Zoom Click Digital Zoom to active this function as abov e.
3. Configure the Camera 21 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 3.7.2 Snapshot Click Snapshot to activate this function. Press Snapshot button to take a picture. The image file is saved as J PEG format into your local PC.
3. Configure the Camera AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 22 Click Reco rd to activate this function. Press Record button to start recording. The video file is saved as ASF format in to your local PC. While you want to stop it, press Stop to stop recording.
3. Configure the Camera 23 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 3.7.5 About Click About to show this ActiveX information.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 24 4 4. Monitor the Image Section 4.1 Monitor the Image Section This function is only available for user logged into Camera as administrator . Click on each menu name to display its setting page.
4. Monitor the Image Section 25 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 4.2 Configure via Web UI 4.2.1 Network Use this menu to configure the network to connect the device and the clients. This section provides the menu fo r connecting the device through Ethernet cable.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 26 IP address, Subnet mask, and Gateway: If you do not select Obtain an IP address automatically , then you need to enter these network parameters manually. Obtain DNS from DHCP: DNS: Stands for Domain Name System.
4. Monitor the Image Section 27 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 4.2.2 DDNS DDNS: Stands for Dynamic Domain Name Server Your Internet Service Provider (ISP) provides you at least one IP address which you use to connect to the Inte rnet.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 28 DDNS: To enable or disable the DDNS service here. Server name: Choose the built-in DDNS server. DDNSHost: The domain name is applied of this device. User name: The user name is used to log into DDNS.
4. Monitor the Image Section 29 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 4.2.3 PPPoE PPPoE: Stands for Point to Point Protocol over Ethernet A standard builds on Ethernet and Point-to-P oint network protocol.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 30 PPPoE: To enable or disable the PPPoE service here. User name: Type the user name for the PPPoE servic e which is provided by the ISP. Password: Type the password for the PPPoE service which is provided by the ISP.
4. Monitor the Image Section 31 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 4.2.5 UPnP UPnP is short for Universal Plug and Play , which is a networking architecture that provides compatibility among networking equipment, software, and peripherals.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 32 UPnP: To enable or disable the UPnP service here. Friendly Name: Shows the friendly name of this device here. UPnP NAT Traversal When enabled, the device will attempt to configure port mapping in a NAT router on your network, using UPnP™.
4. Monitor the Image Section 33 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 4.2.6 Bonjour Bonjour, also known as zero-configur ation networking, enables automatic discovery of computers, devices, and se rvices on IP networ ks.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 34 4.2.7 IP Filter You can enter different user’s IP address which are allowing enter or denying by the device. IP Filter: To enable or disable the IP filter function here.
4. Monitor the Image Section 35 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Subject: Type the subject/title of the E-mail. TCP Notification: If enable this function, then the “ TCP Server “, “ TCP Port ”, and “ Message ” fields need to be filled.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 36 URL: Type the server name or the IP address of the HTTP server. HTTP Login name: Type the user name for the HTTP server. HTTP Login Password: Type the password for the HTTP server.
4. Monitor the Image Section 37 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 4.3 Camera – Adjust Camera Parameters Use this menu to set the functions of the camera parameters of the device. 4.3.1 Picture Rotation: Turn the “Mirror” and “Vertical Flip” On or OFF.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 38 White Balance: Auto: will adjust the white balance automatically. Hold: will hold the white balance. Exposure Control: Auto: will adjust the inte rnal gain automatically.
4. Monitor the Image Section 39 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Name: Name of the specified window. Level Defines the gray level of mask block.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 40 4.4 System – Configure and Maintain Use this menu to perform the prin cipal settings of the device. 4.4.1 System DIPS (Dynamic IP Service): To enable or disable the DIPS® (Dynamic IP Service) function.
4. Monitor the Image Section 41 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual To use this service, just follow four steps below: (1) Enable DIPS function of the device. (2) Check your Device ID from this page. This is a unique number for each device.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 42 Power LED: To turn on or off Power LED. Log: User can check the system log informa tion of the device, including the Main Info , Appended Info , Operator IP , and so on … Reload: Click this button; user can refresh the log information of the device.
4. Monitor the Image Section 43 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Time zone: Set the time difference from Greenwic h Mean Time in the area where the device is installed. Daylight Saving: Disable or enable the dayli ght saving adjustment.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 44 Backup Setting: To take a backup of all of the parameters, click this but ton. If necessary, it will then be possible to return to the prev ious settings, if settings are changed and there is unexpected behavior.
4. Monitor the Image Section 45 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 2. Make sure that only you access this device while firmware updating. 3. Disable Motion Detection function. 4. Click “ Browse ” button. Select the Firmware binary file.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 46 4.5 Video – Configure Profile This device provides 2 modes of video profile. The firs t one is Mega-Pixel mode which supports video resolution up to Mega-pixel. However the maximum frame rate of this mode is up to 15fps only.
4. Monitor the Image Section 47 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Text Overlay Setting: There are some important informati on can be embedded into image, including date, time, and/or text. Video Profile: User can only choose either 720P or 2 Mega modes.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 48 ROI: Assign the selected profile as a ROI stream or not. Rate Control: Defines the rate control method of this profile.
4. Monitor the Image Section 49 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 4.6 Audio – Audio Parameters 4.6.1 Setting.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 50 Audio: To enable or disable audio function Mute While PT: Mute the audio while pan and/or tilt motion Audio Mode: To select Simplex or Fu ll duplex (2-way audio) mode Input Gain: To adjust gain of input audio Output Gain: To adjust gain of output audio 4.
4. Monitor the Image Section 51 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Access Right: Administrator can access every function in this device. However, Viewers only can view the video and access limited function. PTZ Control: Authorize this user to control PTZ function or not.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 52 SMTP Server: Type the SMTP server name or the IP address of the SMTP server. Test: Send a test mail to mail server to che ck this account is available or not. SMTP Port: Set port number of SMTP service.
4. Monitor the Image Section 53 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Add and Del: To add or delete the moti on windows. User can specify up to 10 Included and/or Excluded windows to monitor the video captured by this device.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 54 Sensitivity Defines the sensitivity value of motion detection. The higher value will be more sensitivity. 4.6.5 Storage – Status and Configuration of SD card (POE-200PHD-24 Only) This page shows the status of atta ched SD card.
4. Monitor the Image Section 55 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 4.6.6 Recording List- Files List inside SD Card (IP-200PHD-24 Only) This page shows the files list information. User may play or delete the selected file.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 56 Name: User can specify multiple FTP paths as wish. Therefore, user needs to specify a name for each FTP setting. FTP Server: Type the server name or the IP address of the FTP server.
4. Monitor the Image Section 57 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual FTP Path: Set working directory path of FTP server.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 58 z HTTP Server The device also can send event message to specified HTTP server. Name: User can specify multiple HTTP server s as wish.
4. Monitor the Image Section 59 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Proxy Login name: Type the user name for the HTTP Proxy. Proxy Login Password: Type the password for the HTTP Proxy. Proxy Port: Set port number of Proxy.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 60 SAMBA Login name: Type the user name for the SAMBA server. SAMBA Login Password: Type the password for the SAMBA server. SAMBA Path: Set working directory path of SAMBA server.
4. Monitor the Image Section 61 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Type: Event trigger or Schedule trigger. Enable Time: Define the feasible time slot. Trigger by: Select the triggered sources. Action: Define the actions once event triggered.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 62 Example 2: Send file to E-Mail server by motion tr iggered from Friday 18:00 to Saturday 06:00 1. Select event trigger. 2. Enable time: start from Friday 18: 00 and keep work in 12 hours, so it will stop on Saturday 06:00.
4. Monitor the Image Section 63 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Example 3: Enable Voice Alert every 10-minute during 18:00 to 24:00 from Monday to Friday. 1. Type: Select schedule trigger and interval is 10-minute.
4. Monitor the Image Section AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 64 z Record User can choose the type of record f ile for event or schedule application. Record File Type: Choose JPEG, AVI-JPEG, or AVI-H.264 file format. Record File Prefix: Define the prefix of recorded filename.
4. Monitor the Image Section 65 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Post-Trigger Duration: Define the maximum duration of post-alarm.
5. Troubleshooting & FAQ AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 66 5 5. Troubleshooting & FAQ 5.1 Monitor the Image Section Question Answer or Resolution Features The video and audio codec is adopted in the device. The device utilizes H.
5. Troubleshooting & FAQ 67 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual The device will be installed and work if a firewall exists on the network. If a firewall exists on the network, port 80 is open for ordinary data communication.
5. Troubleshooting & FAQ AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 68 • Maybe UPnP function of NA T router is not compatible to the IP camera.
5. Troubleshooting & FAQ 69 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual • Packet Filtering of the rout er may prohibit access from an external network.
5. Troubleshooting & FAQ AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 70 settings prohibit downloading ActiveX controls”. The device work locally but not externally. • Might be caused from the fi rewall protection. Check the Internet firewall with your system or network administrator.
5. Troubleshooting & FAQ 71 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Pan/Tilt does not work. (including Click to Center and Preset Positioning) • Click [Refresh] on the Internet Explorer when the communication stops with t he device.
5. Troubleshooting & FAQ AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 72 5.2 PING The PING (stands for Packet Internet Gr oper) command is used to detect whether a specific IP address is accessible by sendi ng a packet to the specific address and waiting for a reply.
5. Troubleshooting & FAQ 73 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 5.3 Bandwidth Estimation The frame rate of video transmitted from the device depends on connection bandwidth between client and server, video reso lution, codec type, and quality setting of server.
5. Troubleshooting & FAQ AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 74 5.4 Specification Table Camera IP-200PHD-24/IP-200PHD-24B Image Device 2 Mega-pixel image sensor Effective Pixels 1600 x 1200 pixels Sensitivity 1.0V/lux-sec Signal to Noise 42.
5. Troubleshooting & FAQ 75 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual RTP, RTCP, IGMP, PPPoE, 3GPP, Samba, ICMP Security Password protection, IP address filtering.
5. Troubleshooting & FAQ AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 76 Cell Phone With 3GPP player Video Player VLC, Quick Time, Real Player, Core Player Software Search & Installation IPWizard II Bundled NVR Program CamPro Express 64CH, CamPro HD 5.
5. Troubleshooting & FAQ 77 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual If you have cable or DSL service, you will most likely have a dynamically assigned WAN IP Address. ‘Dynamic’ me ans that your router’s WAN IP address can change from time to time depending on your ISP.
5. Troubleshooting & FAQ AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 78 accessible over the Internet. Th is is accomplished using the Virtual Server function on the router. The Virtual Server ports us ed by the camera must be opened through the router for remote access to your camera .
5. Troubleshooting & FAQ 79 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Enter valid ports in the Virtual Server section of your router. Please make sure to check the box on this line to enable setti ngs. Then the device can be access from WAN by the router’s WAN IP Address.
5. Troubleshooting & FAQ AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 80 Host your own Networked Device and much more no matter what your computer's IP address may be and even if y.
5. Troubleshooting & FAQ 81 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual (3). After the columns show up at the left side, click “ Create Account”.
5. Troubleshooting & FAQ AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 82 (4). Fill the application agreem ent and necessary information.
5. Troubleshooting & FAQ 83 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual (5). Check your e-mail mailbox. There will be an e-mail with a title “Your DynDNS Account Information“. Click the hyperlink addr ess to confirm the DDNS service that you just applied.
5. Troubleshooting & FAQ AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 84 (6). Enter the web page http://www.dyndns.org/ again. Input your username and password that you just applied to login adm inistration interface of DDNS server. Input your account (7).
5. Troubleshooting & FAQ 85 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual (10). Click the “ Get Started ”. (11). We could create a domai n name without any c harge at this step. First, we input the host name. (Pink No.
5. Troubleshooting & FAQ AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 86 4. Setup the DDNS and PPPoE of Netw orked Device At last, users have to enter the web page of Networked Device and setup the necessary information of DDNS and PPPoE a fter the application of DDNS service.
5. Troubleshooting & FAQ 87 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 230V, 240V is within tolerances and commonly found. Austria 230V 50 Hz Brazil 110/220V* 60 Hz *127V found in some states. Please check with your state electricity company.
5. Troubleshooting & FAQ AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 88 5.8 3GPP Table To use the 3GPP function, in addition to previous section, you might need more information or configuration to make this function work.
5. Troubleshooting & FAQ 89 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Click Add or Remove Programs Click Add/Remove Windows Components.
5. Troubleshooting & FAQ AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 90 The following screen will appear: Select Networking Services Select Universal Plug and Play.
5. Troubleshooting & FAQ 91 AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual Click Details Click Next.
5. Troubleshooting & FAQ AirLive IP-200PHD-24/IP-200PHD-24B User’s Ma nual 92 Please wait while Setup configures the components. Click Finish.
An important point after buying a device AirLive IP-200PHD-24 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought AirLive IP-200PHD-24 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data AirLive IP-200PHD-24 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, AirLive IP-200PHD-24 you will learn all the available features of the product, as well as information on its operation. The information that you get AirLive IP-200PHD-24 will certainly help you make a decision on the purchase.
If you already are a holder of AirLive IP-200PHD-24, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime AirLive IP-200PHD-24.
However, one of the most important roles played by the user manual is to help in solving problems with AirLive IP-200PHD-24. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device AirLive IP-200PHD-24 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
