Instruction/ maintenance manual of the product FE-200VD AirLive
Go to page of 73
AirLive FE-200VD Manual 1 FE-200VD 2-Me gaPixel V andal Dome Fish Eye P oE IPCAM Use r ’ s Manual.
Copyright and Disclaimer AirLive FE-200VD Manual i Owner's Record The model and serial numbers are located at the bottom of device. Record these numbers in the spaces provided below . Re fer to these numbers whenever you call upon your dealer regarding this product.
Copyright and Discl aimer AirLive FE-200VD Manual ii For customers in the U.S.A. This equipment has been tested and found to comp ly with the limits for a digit al device, pursuant to Part 15 of the FCC Rules. Th ese limits are designed to provide reasonable protection against harmful interference in a residential installation.
Copyright and Disclaimer AirLive FE-200VD Manual iii NOTICE T O USERS © 2006~1 1 All rights reserved. This manual or the software described herein, in whole or in part, may not be reproduced, translated or reduced to any machine readable form without prior written approval.
T able of Contents i AirLive FE-200VD Manual T able of Content s 1. Intr oducti on ................................................................................................................ .1 1.1 Over view ......................................
T able of Contents AirLive FE-200VD Manual ii 4.4 Schedu le ............................................................................................................ 30 4.4.1 G eneral ................................................................
1. Introduction AirLive FE-200VD Manual 1 1 1. Introduction 1.1 Overview AirLive FE-200VD is a Fish-Eye V andal Dome Network Camera featured with 2Mega Pixel resolution and superior H.264-A VC performance and rich functions. AirLive FE-200VD includes a fish-eye lens for 360° p anor amic wide angle view without blind spot.
1. Introduction AirLive FE-200VD Manual 2 Features z Panoramic 360 Degrees Full View z H.264 & MJPEG V ideo Compression z 2 Megapixels Resolution at 1600 x 1200 pixels z T wo-way Audio Support z Mechanical ICR z Micro SD card for Local S torage z Power-Over-Ethernet 802.
1. Introduction AirLive FE-200VD Manual 3 1.3 Connections 1. RJ45 LAN socket: Connect to PC or Hub/Switch via a 10Base-T Et hernet or 100Base-TX Fa st Ethernet cable. This Ethernet port built with N-Way protocol can detect or negotiate the transmission speed of the network automatically.
1. Introduction AirLive FE-200VD Manual 4 2. DI/DO connector: DI/ DO: Connect to sensor in and alarm out devices Pin Function Description 1 COM 2 RELA Y -NO Digital output implement ation; Pin2 to COM (Pin1) is a Photo-coupled relay on Normal Open status.
1. Introduction AirLive FE-200VD Manual 5 6. Line out (audio out) Connect a loud speaker to the network camera . This function is for voice alerting and two-way audio. 7. BNC Connector The composite video format will be sent out through this connector .
1. Introduction AirLive FE-200VD Manual 6 4. Mount the camera onto the suit able position, and then fasten the screws. 5. Close the cove r and fasten the screws. 1.5 Inst all the Camera in LAN 1. Plug an Ethernet cable into the Camera Connect an Ethernet cable to the LAN so cket and attach it into the network.
2. Preparation AirLive FE-200VD Manual 7 2 2. Prep aration 2.1 Search and Set up by IPWizard II When you install the Camera on a LAN environment, you have two easy ways to search your Camera by IPWizard II or UPnP™ discovery . Here is t he way to execute IPWizard II to discover Camera’ s IP address and set up related p arameter in a Camera.
2. Preparation AirLive FE-200VD Manual 8 2.2 UPnP of Windows® XP , V ist a or 7 UPnP™ is short for Universal Plug and Play , which is a networking architecture that provides compatibility among networking equipment, sof tware, and peripherals. This device is an UPnP enabled device.
2. Preparation AirLive FE-200VD Manual 9 Click the targeted Device . Then Internet Explorer will connect to this Network Camera automatically . 2.3 Inst all the Device behind a NA T Router Once installed, the device is accessible on your LAN.
2. Preparation AirLive FE-200VD Manual 10 (2) Enable UPnP NA T traversal opt ion of the Netw ork Camera Refer to Setting Î Network Î UPnP page for det ail NA T traversal setting. Note that this option is default enabled. (3) Access your Network Camera by DIPS Refer to Setting Î System Î System p age for detail DIPS information.
2. Preparation AirLive FE-200VD Manual 11 3. According your browser ’s security setting, the IE W eb Page may prompt the “Security W arning” window . If so, select “Y es” to insta ll and run the ActiveX control into your PC. Otherwise, the system will load the ActiveX silently .
3. Operating the Network Camera AirLive FE-200VD Manual 12 3 3. Operating the Network Camera S tart-up screen will be as follow no matter an ordinary users or an administrator . Configuration Click for configuring the camera settings. Language The device can provide multiple languages to meet customer ’s requirement.
3. Operating the Network Camera AirLive FE-200VD Manual 13 V ideo Profile The device supports multi-profile function for H.264, MEPG4 and JPEG simult aneously . A user can chose the proper and/or preferred profile which is listed here. Protocol User can select proper streaming protocol according to networking environment.
3. Operating the Network Camera AirLive FE-200VD Manual 14 z Quad view & Quad with source view PTZ control panel: 1. Ch ： Select the channel. (1~4) & (2~4) 2. S tep ： Set the speed of Pan/T ilt Function. (1~10) 3. Pan/T ilt Arrow ： Click to control the Pan/T ilt Function.
3. Operating the Network Camera AirLive FE-200VD Manual 15 Vo l u m e Click S peaker button to activate this function. Scroll the control bars to adjust the audio attribute. Full Screen Enlarge video to full screen display . Pre ss “ESC” key to disable this function.
4. Administrating the Device AirLive FE-200VD Manual 16 4 4. 0B Administrating the Device System Setting This function is only available for a user logs into Camera as administrator . Click on each menu name to display its setting p age. Item Action V ideo Configure bit rate and fr ame rate of video profiles.
4. Administrating the Device AirLive FE-200VD Manual 17 4.1.2 Advanced z S tream Setting Note: Configuration of stream 2 is the same as stream 1, but S tream 2 can only be set to 320x240 or 640x480. z R TSP Path The R TSP Path is the stream ID used for R TSP client streaming connection, such as VLC player .
4. Administrating the Device AirLive FE-200VD Manual 18 z Image Format H.264 and MJPEG are available for image fo rmat selection. The term, “image format”, is referring to compression / encodi ng technique. The selection of image format decides the performance of bandwid th and storage requirement.
4. Administrating the Device AirLive FE-200VD Manual 19 4.2 Camera: Adjust Camera Parameters Use this menu to set the functions of the camera p arameters of the device. 4.2.1 General Use this function to determine the Auto Con trast Compensation level.
4. Administrating the Device AirLive FE-200VD Manual 20 z Audio Setting: Audio Enable: T urn on/off the audio. z Web Record Setting: Save Path / File name: Click on the “Browse” button to select the desired p ath to save as well as naming the video file.
4. Administrating the Device AirLive FE-200VD Manual 21 4.2.2 Advanced z White balance: Adjustment to compensate for different envir onments in terms of light source. A user can choose auto/hold/sunny/cloudy /indoor , so FE-200VD can determine the correct color compensation due to different light environment.
4. Administrating the Device AirLive FE-200VD Manual 22 z Infrared (IR) Cut Filter: The default is automatically switched accord ing to the light intensity . “Enable” indicates the filter is enable to cut IR light to make sure t he color is correct.
4. Administrating the Device AirLive FE-200VD Manual 23 (3) Quad with source view: (4) T riple view: 2. Ceiling Mount: For Choosing Ceiling mount, go back to liv e view . There are 6 kinds of video layout to choose from Original view , Broad view , Quad view , Quad with source view , Double view and T riple view .
4. Administrating the Device AirLive FE-200VD Manual 24 (2.) Broad view: (3.) Quad view: (4.) Quad with source view: (5.) Double view:.
4. Administrating the Device AirLive FE-200VD Manual 25 (6.) T riple view: 4.3 Event 4.3.1 Event Server 5. Add FTP Server: Click on the “Add FTP” to exp and FTP server setting.
4. Administrating the Device AirLive FE-200VD Manual 26 z Add HTTP Server: Click on the “Add HTTP ” to exp and HTT P server setting. HTTP Server: Name: Give a name for the HTTP server URL: Input the network address of the HTTP server Username / Password: I nput the username and pa ssword of the HTTP .
4. Administrating the Device AirLive FE-200VD Manual 27 4.3.2 Motion Detection z T o add a motion detection area: 1. Click on “Add” to set up a detecti on area. (Setup p anel will be expanded) 2. Give a name to this window area. 3. Select the trigger level and sensitivity for this detection window .
4. Administrating the Device AirLive FE-200VD Manual 28 5. Draw detection window on the image. 6. Once everything is done, click on “Sav e” to save the c onfiguration made. Configured detection window will be displayed in motion detection list. (Circled in blue) Note: 1.
4. Administrating the Device AirLive FE-200VD Manual 29 4.3.3 I/O Ports AirLive FE-200VD supports 1 photo-coupled re lay inputs and 1 relay output s. Refer to “ Appendix A: I/O T erminal Connectors ” for detail pin description and application. The below table shows the st atus of t he external trigger/alarm devices.
4. Administrating the Device AirLive FE-200VD Manual 30 5. The trigger condition is Motion Detection. The responding actions can be “Upload images” and “Act ivate Output Port” and “Send Email Notification” and “Send HTTP Noti fication to” and “Send Message Notification (TCP)”.
4. Administrating the Device AirLive FE-200VD Manual 31 4.5 Network 4.5.1 General Device IP configuration, in cludes DHCP and S tatic IP setti ng. “Enable ARP/Ping” enable device to accept ARP or ping pa ckets from the network. Disable this option may provide extra security from intentional ping.
4. Administrating the Device AirLive FE-200VD Manual 32 Enable this checked box when a DHCP server is installed on the network to issue IP address assignment. With this setting, the IP address is assigned automatically . If this device can not get an IP address within li mited tries, the device will assign to the default IP address, 192.
4. Administrating the Device AirLive FE-200VD Manual 33 4.5.2 Advanced Enable or configure other network functions. z NTP: Configure a NTP (Network T ime Protocol) se rver , so that the device system date and time can be synchronized with a specif ied T ime Server or DHCP server .
4. Administrating the Device AirLive FE-200VD Manual 34 4.5.4 DDNS (Dynamic DNS) Dynamic DNS configuration; the network device can be assigned with a host name by registering this service (Internet access required).
4. Administrating the Device AirLive FE-200VD Manual 35 4.6 System 4.6.1 Information Lists - System and Network configurations. z Firmware V ersion: This information shows the firmware version of the device. 4.6.2 User Use this menu to add, update, or remove the usernames and passwords of the Administrator and viewer .
4. Administrating the Device AirLive FE-200VD Manual 36 4.6.3 Day & Time Y ou can setup the device or make it synchroni zed with PC or remote NTP server . Also, you may select your time zone in order to synchronize time locally . z Current Server T ime: Displaying the date and ti me of the device.
4. Administrating the Device AirLive FE-200VD Manual 37 z Reboot: The device is restarted without changing any of the network settings. I t means the IP address of the device will not change after firmware upgrade. z Load Default (Excluding Network setting): The unit is restarted and most current sett ings are reset to fa ctory default values.
4. Administrating the Device AirLive FE-200VD Manual 38 1. Close all other application programs whic h are not necessary for firmware update. 2. Make sure that only you access this device while firmware updating. 3. Disable Motion Detection function. 4.
4. Administrating the Device AirLive FE-200VD Manual 39 4.6.5 Log Service Most system operations and / or process will be kept in a log system. The link provides the review of these records.
4. Administrating the Device AirLive FE-200VD Manual 40 z Use Custom Settings: The allowed modifications are changing of Background / T ext Color , Background picture, T itle, Descrip tion, Logo Link and Logo.
5. Appendix AirLive FE-200VD Manual 41 5 5. 0B Appendix Appendix A: Alarm I/O Connector This Network Camera provides a general I/O terminal block. Pin Function Description 1 COM 2 RELA Y -NO Digital output implement ation; Pin2 to COM (Pin1) is a Photo-coupled relay on Normal Open status.
5. Appendix AirLive FE-200VD Manual 42 z Explanation of External I/O Circuit Diagram: z CAUTION! − THE LOW VOL T AGE/ CURRENT CIRCUITS AND HIGH VOL T AGE / CURRENT CIRCUITS ARE IN THE NETWORK CAME RA CIRCUIT . THE QUALIFIED ELECTRICIAN SHOULD DO THE WIRING NOT BY YOURSELF .
5. Appendix AirLive FE-200VD Manual 43 Appendix B: T roubleshooting & Frequently Asked Questions Question Answer or Resolution Features The video and audio codec is adopted in the device. The device utilizes H.264, MPEG4 and JPEG triple compression to providing hi gh quality images.
5. Appendix AirLive FE-200VD Manual 44 The username and password for the first time or after facto ry default reset Username = admin and Password = airlive . Note that it’ s all case sensitivity . Forgot the username and password Follow the steps below .
5. Appendix AirLive FE-200VD Manual 45 Can not work with NA T router • Maybe NA T router does not support UPnP function. Please check user ’s manual of router and turn on UPnP function. • Maybe UPnP function of NA T router is not compatible to the IP camera.
5. Appendix AirLive FE-200VD Manual 46 Cannot access the login page and other web pages of the Network Camera from Internet Explorer • Maybe the IP Address of the Network Camera is already being used by another device or computer .
5. Appendix AirLive FE-200VD Manual 47 Image or video does not appear in the main page. • The first ti me the PC connects to Network Camera, a pop-up Security W arning window will appear to download ActiveX Controls. When using Windows XP , or V ista, log on with an appr opriate account that is authorized to install applications.
5. Appendix AirLive FE-200VD Manual 48 The unreadable characters are displayed. Use the operating system of the selected language. Set the Encoding or the Char acter Set of the selected language on the Internet Explorer . Frame rate is slower than the setting.
5. Appendix AirLive FE-200VD Manual 49 The color of the image is poor or strange. • Adjust White Balanc e. • T o insure the images you are viewing are the best they can be, set the Display property setting (color quality) to 16bit at least and 24 bit or hi gher if possible within your computer .
5. Appendix AirLive FE-200VD Manual 50 If you want to detect any other devices conf licts with the IP address of Network Camera, also can utilize the PING command but you must disconnect the device from the network first.
5. Appendix AirLive FE-200VD Manual 51 (SXGA) per frame @ 15fp s Note : Audio streaming also takes bandwidth around 32kbp s. Some xDSL/Cable modem upload speeds could not even reach up to 128 kbps. Thus, you may not be able to receive good quality video while also streaming audio on a 128 kbps or lower connection.
5. Appendix AirLive FE-200VD Manual 52 Motion Detection Up to 10 motion detection areas with included or excluded options Alarm Events File upload via FTP ,SD Card or email Notification via email, HTTP , External output activation General RAM 128MB ROM 2GB Power Supply 12V DC external power adapter PoE IEEE 802.
5. Appendix AirLive FE-200VD Manual 53 Manually installing the device with a router on your network is an easy 3–step procedure as following: (1) Assign a local/fixed IP address to your device (.
5. Appendix AirLive FE-200VD Manual 54 Y our W AN IP Addre ss will be listed here. Note : Because a dynamic WA N IP can change from time to time depending on your ISP , you may want to obtain a S tatic IP address from your ISP .
5. Appendix AirLive FE-200VD Manual 55 Private Port section, click Apply . • Scheduling should be set to Always so that the camera images can be accessed at any time. A check mark appearing before the entry name will indi cate that the ports are enabled.
5. Appendix AirLive FE-200VD Manual 56 Appendix G: DDNS Application z Preface If you have a Cable modem or xDSL, this is a great way to host your own Networked Device or other TCP/IP Service. Ge t your own domain lik e www .yourname.com, www .yourname.
5. Appendix AirLive FE-200VD Manual 57 (3). After the columns show up at the left side, click “ Create Account ”. (4). Fill the application agreem ent and necessary information. a. Username b. E-mail address and confirmation c. Password and confirmation d.
5. Appendix AirLive FE-200VD Manual 58 (5). Check your e-mail mailbox. There will be an e-mail with a title “Y our DynDNS Account Information“. Click the hyperlink addr ess to confirm the DDNS service that you just applied. Then DDNS you applied activated.
5. Appendix AirLive FE-200VD Manual 59 (6). Enter the web page http://www .dyndns.org/ again. Input your username and password that you just applied to login adm inistration interface of D DNS server . (7). If the correct username and password are input, you can see the following picture at the top-right of the login page.
5. Appendix AirLive FE-200VD Manual 60 (8). Click the “ Services ”. (9). Click the “ Dynamic DNS ”. (10). Click the “ Get S tarted ”..
5. Appendix AirLive FE-200VD Manual 61 (1 1). We could create a domain name without any c harge at this step . First, we input the host name. (Pink No.1) Then we pick a domai n that is easy to remember . (Pink No.2) The 3rd step is to click “Of fline Hostname” fr om Service T ype.
5. Appendix AirLive FE-200VD Manual 62 Appendix H: Power Line Frequency COUNTRY VOL T AGE FREQUENCY COMMENTS Argentina 220V 50 Hz *Neutral and line wires are reversed from that used in Australia and elsewhere. Australia 230V* 50 Hz *Outlets typically controlled by adjacent switch.
5. Appendix AirLive FE-200VD Manual 63 Portugal 230V 50 Hz S pain 230V 50 Hz Sweden 230V 50 Hz Switzerland 230V 50 Hz T aiwan 1 10V 60 Hz Thailand 220V 50 Hz United Kingdom 230V* 50 Hz *Outlets typically controlled by adjacent switch. Though nominal voltage has been officially changed to 230V , 240V is within tolerances and commonly found.
5. Appendix AirLive FE-200VD Manual 64 Appendix J: Enable UPnP of Windows XP Use the following steps to enable UPnP settings only if your operati ng system of PC is running Windows XP .
5. Appendix AirLive FE-200VD Manual 65 Click Add/Remove Windows Components The following screen will appear: Select Networking Services Click Details.
5. Appendix AirLive FE-200VD Manual 66 Select Universal Plug and Play Click Ok Click Next.
5. Appendix AirLive FE-200VD Manual 67 Please wait while Setup configures the components. Click Finish.
An important point after buying a device AirLive FE-200VD (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought AirLive FE-200VD yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data AirLive FE-200VD - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, AirLive FE-200VD you will learn all the available features of the product, as well as information on its operation. The information that you get AirLive FE-200VD will certainly help you make a decision on the purchase.
If you already are a holder of AirLive FE-200VD, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime AirLive FE-200VD.
However, one of the most important roles played by the user manual is to help in solving problems with AirLive FE-200VD. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device AirLive FE-200VD along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
