Instruction/ maintenance manual of the product DW705 DeWalt
Go to page of 19
English.
D E WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 Printed in U.S.A. (FEB02-CD-1) Form No. 386782-01 DW705 Copyright 2001, 2002.
DW705 (120 V olt)/DW705 (220 V olt) 12" Compound Miter Saw Scie à lnglets 300 mm (12 po) Sierra de àngulo compuesto 300 mm (12") INSTRUCTION MANUAL GUIDE D´UTILISA TION MANUAL DE INSTRUCCIONES INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.
English T able of Contents DOUBLE INSULATION/POLARIZED PLUG INSTRUCTIONS ....................................1 SAFETY INSTRUCTIONS FOR ALL TOOLS ......…………………………………………1 ADDITIONAL SAFETY RULES ........……………………………………………………….
English Important Safety Instructions WARNING: When using electric tools, basic safety precautions should always be followed to reduce risk of fire, electric shock, and personal injury, including the .
English • DO NOT - Move either hand from saw or workpiece or raise arm until blade has stopped. • DO NOT - Use without Kerf Plate or when kerf slot is wider than 3/8". CAUTION: Wear appropriate personal hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.
English 3 Electrical Connection Be sure your power supply agrees with the nameplate marking. 120 volts, AC/DC means that your saw will operate on alternating or direct current. A voltage decrease of 10 percent or more will cause a loss of power and overheating.
English FIG. 3 45 55 40 3 5 5 0 4 5 FIG. 4 LOCK DOWN PIN Accessories Recommended accessories for use with your tool are available at extra cost from your local service center. CAUTION: The use of any non-recommended accessory such as dado sets, molding cutters, or abrasive wheels may be hazardous.
5 English ALWA YSADJUST FENCE PROP ERLYBEFOR EUSE DW7050 DW7051 SELF-TAPPING STUD LOCKNUTS END PLATE CLAMPING BRACKET STOP WASHER AND SCREW KNOBS BOTTOM HOLE (USE IF ON RIGHT SIDE) BRACKET TOP HOLE (USE IF ON LEFT SIDE) As shown in Figure 6 the inner clamp washer is installed first, then the blade adapter.
6 English Stop as shown in Figure 12, and adjust the stop screw as necessary. Hold the stop screw in place and tighten the lock nut. BEVEL POINTER If the bevel pointer does not indicate zero, loosen the screw that holds it in place and move the pointer as necessary.
7 English 45 45 40 50 3 5 55 30 6 0 25 65 2 0 7 0 1 5 7 5 45 45 40 50 35 55 30 6 0 0 5 15 20 25 30 35 10 15 20 25 30 35 22.5 31.62 22.5 31.62 75 70 65 60 55 75 70 65 60 55 85 9 0 80 1 1 2 1 1 2 FIG.
8 English FIG. 11B STOP SCREW LOCK NUT FIG. 12 BEVEL POINTER SCREW BEVEL STOP FIG. 11A BEVEL HOUSING one that best fits your needs. (Page 3) BODY AND HAND POSITION (SEE FIG. 16) Proper positioning of your body and hands when operating the miter saw will make cutting easier, more accurate and safer.
9 English ALWAYSADJUSTFENCE PROPERLYBEFOREUSE D ANGE R K EE P A WA Y F R OM BL AD E FIG. 14 FIG. 15 TRIGGER SWITCH GUIDE GROOVE HOLE FOR PADLOCK LEFT SIDE FENCE CLAMPING KNOBS FIG. 13 LEFT SIDE BEVEL STOP SCREW with it. Example: To make a 4 sided box with 26° exterior angles (Angle A, Figure 19), use the upper right arc.
10 English ALWAYSA DJUSTFENCE PROPERLYBEFOREUS E D A N GER K EE P AW A Y F RO M BL ADE D A N G E R K E E P A W A Y F R O M B L A D E IMPROPER CUT IMPROPER CUT PROPER CUT 2. Save left side of cut Right side 1. Miter Right 45° 2. Save right side of cut OUTSIDE CORNER: Left side 1.
11 English FIG. 17 FIG. 18 FIG. 19 A. B. ANGLE “A” 0 5 15 20 25 30 35 10 15 20 25 30 22.5 31.62 22.5 31.62 75 70 65 60 55 75 70 65 60 85 9 0 80 1 1 2 1 1 2 FIG.
12 English FIG. 23 FIG. 24 accurately set on your saw.) Since most rooms do not have angles of precisely 90 degrees, you will have to fine tune your settings anyway. PRETESTING WITH SCRAP MATERIAL IS EXTREMELY IMPORTANT! INSTRUCTIONS FOR CUTTING CROWN MOLDING LAYING FLAT AND USING THE COMPOUND FEATURES 1.
13 English This way, when corners other than 90 degrees are encountered, the saw can be quickly and easily adjusted for them. Use the crown molding fence accessory to maintain the angle at which the molding will be on the wall. INSTRUCTIONS FOR CUTTING CROWN MOLDING ANGLED BETWEEN THE FENCE AND BASE OF THE SAW FOR ALL CUTS: 1.
14 English Important To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.
15 English Tr ouble Shooting Guide BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS TROUBLE! SAW WILL NOT START WHAT’S WRONG? WHAT TO DO… 1. Saw not plugged in 1. Plug in saw. 2. Fuse blown or circuit breaker tripped 2. Replace fuse or reset circuit breaker 3.
An important point after buying a device DeWalt DW705 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought DeWalt DW705 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data DeWalt DW705 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, DeWalt DW705 you will learn all the available features of the product, as well as information on its operation. The information that you get DeWalt DW705 will certainly help you make a decision on the purchase.
If you already are a holder of DeWalt DW705, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime DeWalt DW705.
However, one of the most important roles played by the user manual is to help in solving problems with DeWalt DW705. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device DeWalt DW705 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
