Instruction/ maintenance manual of the product DW515K DeWalt
Go to page of 22
DW505 T aladr o Per cutor 13 mm (1/2") 1/2" (13 mm) Dual Speed Range Hammer drill INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. MANUAL DE INSTRUCCIONES INSTRUCTION MANUAL ¿Dudas? Visítenos en Internet: www.
.
3 Español 3 Defi niciones: Normas de seguridad Las siguientes definiciones describen el nivel de gravedad de cada advertencia. Lea el manual y preste atención a estos símbolos. PELIGRO: indica una situación de peligro inminente que, si no se evita, provocará la muerte o lesiones graves.
4 Español 4 f) Si no se puede evitar el uso de una herramienta eléctrica en una zona húmeda, utilice un dispositivo de corriente residual (residual current device, RCD) de seguridad. El uso de un RCD reduce el riesgo de sufrir una descarga eléctrica.
5 Español 5 e) Mantenimiento de las herramientas eléctricas. Revise que no haya piezas en movimiento mal alineadas o trabadas, piezas rotas o cualquier otra situación que pueda afectar el funcionamiento de las herramientas eléctricas. Si encuentra daños, haga reparar la herramienta eléctrica antes de utilizarla.
6 Español 6 T ensión (V oltios) Longitud del cable en metros (m) 120–127 V 0–7 7–15 15–30 30–50 220–240 V 0–15 15–30 30–60 60–100 Corriente nominal (Amperios) Sección nominal m.
7 Español 7 ........Construcción Clase I .......... terminal a tierra (con conexión a tierra) ......... símbolo de alerta de .........Construcción Clase II seguridad (con aislamiento doble) …/min ... revoluciones o BPM ....golpes por minuto reciprocidad por sfpm .
8 Español 8 P ALANCA DE REVERSA INTERRUPTOR DE GA TILLO BOTÓN DEL SEGURO FIG. 2 VELOCIDAD V ARIABLE El interruptor de gatillo de velocidad variable permite controlar la velocidad. Cuanto más fuerte se pulse el interruptor de gatillo, mayor será la velocidad del taladro per cutor .
9 Español 9 Selector del modo de martillo o de taladro (Fig. 4) Para cambiar la herramienta del modo de taladro al de martillo (o viceversa) gire el selector hasta la posición que desee, como se muestra en la Figura 4. Para taladrado simple, alinee el símbolo de la broca con el portabrocas.
10 Español 10 6. Haga funcionar el motor al r etirar la broca del interior del orificio. Esto evitará que se atasque. 7. Con los taladros de velocidad variable no hay necesidad de hacer una marca de centrado con un punzón.
11 Español ADVERTENCIA: Nunca utilice disolventes u otros productos químicos abrasivos para limpiar las piezas no metálicas de la herramienta. Estos productos químicos pueden debilitar los materiales plásticos utilizados en estas piezas. Utilice un paño humedecido sólo con agua y jabón neutro.
12 English Defi nitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please r ead the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury .
13 English c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/ or battery pack, picking up or carr ying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
14 English • Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. • W ear safety goggles or other eye protection. Drilling operations cause chips to fly .
15 English W ARNING: Always use eye protection. All users and bystanders must wear eye protection that conforms to ANSI Z87.1. • The label on your tool may include the following symbols. The symbols and their definitions are as follows: V ..........
16 English High/Low Speed Operation (Fig. 3) The two speed gear drive in the dual range hammerdrill permits effective operation over an extended range of applications with greater selection of accessories.
17 English For straight drilling, align selector with drill bit symbol. For hammering, align selector with the hammer symbol, as shown in the figure. NOTE: The selector must be in either drill or hammer/drill mode at all times. There ar e no operable positions between the two.
18 English MAINTENANCE WARNING: T o reduce the risk of injury , turn unit off and disconnect tool from power source before installing and removing accessories, before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury .
19 English MAXIMUM RECOMMENDED CAP ACITIES DW505 CHUCK CAP ACITY 1/2" (13 mm) R.P .M. 0–1,100 – 0–2,700 BITS, MET AL DRILLING 3/8" (10 mm) low speed WOOD, FLA T BORING 1-1/2" (38 mm) low speed BITS, MASONRY DRILLING 3/4" (19 mm) soft materials HOLE SAWS 2-1/8" (53.
.
.
D E W AL T Industrial T ool Co., 701 East Joppa Road, Baltimore, MD 21286 (NOV11) Part No. N142137 DW505 Copyright © 2003, 2006, 2011 D E WAL T The following are trademarks for one or mor e D E W AL .
An important point after buying a device DeWalt DW515K (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought DeWalt DW515K yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data DeWalt DW515K - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, DeWalt DW515K you will learn all the available features of the product, as well as information on its operation. The information that you get DeWalt DW515K will certainly help you make a decision on the purchase.
If you already are a holder of DeWalt DW515K, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime DeWalt DW515K.
However, one of the most important roles played by the user manual is to help in solving problems with DeWalt DW515K. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device DeWalt DW515K along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
