Instruction/ maintenance manual of the product RL2718PA/NA Desa
Go to page of 40
Sav e this manual for future reference. For more information, visit www .desatech.com UNVENTED (VENT -FREE) GAS LOG HEA TER OWNER’S OPERA TION AND INST ALLA TION MANU AL Biltmore Split Oak, Seasonal.
www .desatech.com 1 13097-01E 2 - .
www .desatech.com 1 13097-01E 3 SAFETY INFORMATION - .
www .desatech.com 1 13097-01E 4 4. If you smell gas • shut off gas supply • do not try to light any appliance • do not touch any electrical switch; do not use any phone in your building • immediately call your gas supplier from a neighbor’s phone.
www .desatech.com 1 13097-01E 5 Figure 1 - V ent-Free Gas Log Heater (Logs May V ary by Model, Seasonal Oak Single Burner Model Shown) Base Grate Log Set Control Knob Burner Piezo Ignitor PRODUCT IDENTIFICATION PRODUCT FEA TURES OpERA TION This heater is clean burning.
www .desatech.com 1 13097-01E 6 Exhaust fans, replaces, clothes dryers and fuel burni ng appl iances draw a ir fro m the h ouse t o operate. Y ou must provide adequate fresh air for these appliances. This will insure proper venting of vented fuel-burning appliances.
www .desatech.com 1 13097-01E 7 Example: Gas water heater ____________ Btu/Hr V ent-free replace + ___________ Btu/Hr T otal = ___________ Btu/Hr 4.
www .desatech.com 1 13097-01E 8 INST ALLA TION .
www .desatech.com 1 13097-01E 9 W.
www .desatech.com 1 13097-01E 10 Y ou must have noncombustible material(s) above the replace opening. Noncombustible materials (such as slate, marble, tile, etc.) must be at least 1/2 inch thick. With sheet metal, you must have noncombustible material behind it.
www .desatech.com 1 13097-01E 1 1 not meet the minimum clear- ances shown, you must do o.
www .desatech.com 1 13097-01E 12 Se e c ha rt bel ow for mi ni mum p erm an ent ue opening you must provide. Attach damper clamp so the minimum permanent ue opening will be maintained at all times.
www .desatech.com 1 13097-01E 13 INST ALLA TION Continued 7. Mark screw locati ons through holes in mount - ing brackets (see Figure 12 and 13). If install - ing in a brick-bottom replace, mark screw locations in mortar joint of bricks. 8. Remove heater base from replace.
www .desatech.com 1 13097-01E 14 For propane/LP units, the installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce inco min g gas press ure to betwee n 11 and 14 inch es of water. If you do not reduce incoming gas pres - sure, heater regulator damage could occur.
www .desatech.com 1 13097-01E 15 INST ALLA TION Continued - .
www .desatech.com 1 13097-01E 16 INSTALLING LOGS - .
www .desatech.com 1 13097-01E 17 INST ALLA TION Continued Figure 22 - Installing Crossover Log #4 (CCL3930PTB/NTB Shown) Middle Log (#2) Back Log (#3) Pins Crossover Log (#4) 5.
www .desatech.com 1 13097-01E 18 INST ALLA TION Continued .
www .desatech.com 1 13097-01E 19 OPERATING HEATER MANUALLY-CONTROLLED MODELS FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not fol- low these instructions exactly, .
www .desatech.com 1 13097-01E 20 5. Slightly depress and turn control knob counterclockwise to the PILOT position. Press in control knob for ve (5) seconds (see Figure 30). Note: You may be running this heater for the rst time after hooking up to gas sup - ply.
www .desatech.com 1 13097-01E 21 THERMOST A T -CONTROLLED MODELS FOR YOUR SAFETY READ BEFORE LIGHTING W ARNING: If you do not fol- low these instructions exactly , .
www .desatech.com 1 13097-01E 22 5. Tu rn co nt ro l kno b co unt ercl ockw ise to the PILOT position. Press in control knob for ve (5) seconds (see Figur e 32). Note: Y ou may be running this heater for the rst time after hooking up to gas sup - ply .
www .desatech.com 1 13097-01E 23 INSPECTING B URNERS Check pilot ame pattern and burner ame pat - terns often. pILOT FLAME p A TTERN Figure 34 sh ows a cor rec t pil ot a me pa tt ern . Figure 35 sh ow s an in co rr ec t pi lo t am e pa tt er n.
www .desatech.com 1 13097-01E 24 2. Ins pect bur ner , pil ot and primar y air inlet hole s on injector holder for dust and dirt (see Figure 36). 3. Blow air through the ports/slots and holes in the burner . 4. Check the injector holder located at the end of the burner tube again.
www .desatech.com 1 13097-01E 25 TROUBLESHOO TING .
www .desatech.com 1 13097-01E 26 TROUBLESHOO TING Continued 1. Burner orice clogged 2. Inlet gas pressure is too low 1. Manifold pressure is too low 2. Burner orice clogged 1. Burner orice is clogged or damaged 2.
www .desatech.com 1 13097-01E 27 TROUBLESHOO TING Continued .
www .desatech.com 1 13097-01E 28 OPTIONAL POSITIONING OF THERMOST A T SENSING B ULB .
www .desatech.com 1 13097-01E 29 4. The mounting clip must be a minimum of 3" from bottom of replace to prevent crimping of capillary . Once you have decided on a location, clean the area thoroughly . Remove the paper backing from the adhesive on back of mounting clip.
www .desatech.com 1 13097-01E 30 ILL USTRA TED P ARTS BREAKDOWN .
www .desatech.com 1 13097-01E 31 P ARTS LIST This list contains replaceable parts used in your heater.
www .desatech.com 1 13097-01E 32 ILL USTRA TED P ARTS BREAKDOWN .
www .desatech.com 1 13097-01E 33 P ARTS LIST This list contains replaceable parts used in your heater.
www .desatech.com 1 13097-01E 34 ILL USTRA TED P ARTS BREAKDOWN .
www .desatech.com 1 13097-01E 35 P ARTS LIST This list contains replaceable parts used in your heater.
www .desatech.com 1 13097-01E 36 ILL USTRA TED P ARTS BREAKDOWN .
www .desatech.com 1 13097-01E 37 P ARTS LIST This list contains replaceable parts used in your heater.
www .desatech.com 1 13097-01E 38 REPLACEMENT P ARTS Note: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty .
www .desatech.com 1 13097-01E 39 5 Manila A ve Hamden, CT 06514-0322 1-800-397-7553 203-248-7553 342 N. County Rd. 400 East V alparaiso, IN 46383-9704 219-462-7441 1-888-619-7060 www .
Model Serial No. Date Purchased WARRANTY INFORMA TION KEEP THIS WARRANTY Always specify model and serial numbers when communicating with the factory . W e reserve the right to amend these specications at any time without notice. The only warranty applicable is our standard written warranty .
An important point after buying a device Desa RL2718PA/NA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Desa RL2718PA/NA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Desa RL2718PA/NA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Desa RL2718PA/NA you will learn all the available features of the product, as well as information on its operation. The information that you get Desa RL2718PA/NA will certainly help you make a decision on the purchase.
If you already are a holder of Desa RL2718PA/NA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Desa RL2718PA/NA.
However, one of the most important roles played by the user manual is to help in solving problems with Desa RL2718PA/NA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Desa RL2718PA/NA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
