Instruction/ maintenance manual of the product 36-585 Delta
Go to page of 21
INSTRUCTION MANUAL 10" Dual Bevel Compound Miter Saw (Model 36-585) P ART NO. 910638 - 01-30-04 Copyright © 2004 Delta Machinery ESP AÑOL: PÁGINA 21 T o learn more about DEL T A MACHINER Y visit our website at: www .
2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
3 1. FOR YOUR OWN SAFETY , READ THE INSTRUCT - TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. USE CERTIFIED SAFETY EQUIPMENT .
4 ADDITIONAL SAFETY RULES FOR MITER SA WS Refer to them often and use them to instruct others . F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS INJUR Y . 04-24-03 SA VE THESE INSTRUCTIONS . 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions.
5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug.
6 Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cord which has a 3-pr ong grounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine.
7 CAR TON CONTENTS Fig. 2 Remove the miter saw and all loose items from the carton. Lifting the miter saw by the switch handle can cause misalignment. Always lift the machine by the base or the carrying handle (4) Fig. 2). 1 2 3 4 5 6 1. Miter Saw 2. W ork Clamp 3.
8 DUST BAG Depress the dust bag spring clips (A) Fig. 6, and secur e the dust bag (B) between the ridges of the spout (C). Fig. 6 WORK CLAMP T wo holes (A) and (B) Fig.
9 OPERA TING CONTROLS AND ADJUSTMENTS HAZARD ZONE The area inside the two r ed lines (A) Fig. 9 on the table is designated as a “Hazard Zone”. NEVER place your hands inside this area while the machine is running. Fig. 9 ST AR TING AND STOPPING MITER SA W T o start the miter saw , depress the switch trigger (A) Fig.
10 Fig. 14 Fig. 15 Fig. 16 Fig. 17 ROT A TING T ABLE FOR MITER CUTTING Y our miter saw will cut any angle from 90° to 47°, right and left. Pull out on the lock handle (A) Fig. 14. T ur n the lock handle one or two turns counter -clockwise, depress the index lever (B), and move the table to the desir ed angle.
11 Fig. 18 Fig. 19 ADJUSTING 90° AND 45° DEGREE BEVEL STOPS DISCONNECT MACHINE FROM POWER SOURCE. 1. Lock the machine in the “down” position. 2. Place one end of a square (A) Fig. 18 on the table and the other end against the blade. V erify that the blade is 90° to the table (Fig.
12 Fig. 23 When bevel cutting, move the fence (A) Fig. 23 away from the blade to allow for clearance for the saw blade and guard. T o accomplish this, lift up on the fence tension knob (B) Fig. 22, slide the fence to the desired location, and push down on the fence tension knob to lock the fence.
13 Fig. 27 ADJUSTING TENSION OF CUTTINGHEAD RETURN SPRING The tension of the cuttinghead return spring was set at the factory to return to the “up” position. If necessary , to adjust: Loosen the nut (A) Fig. 27 and tur n the screw (B) (clockwise to increase or counter clockwise to decrease the spring tension).
14 Holes are pr ovided in the fence to attach an auxiliary fence. This auxiliary fence is constructed of straight wood approximately 1/2" thick by 3" high by 20" long. Use the auxiliary fence (A) ONL Y with the saw blade in the 0° bevel position (90° to the table).
15 Fig. 37 Fig. 38 CUTTING ALUMINUM Y ou can easily cut aluminum extrusions (for making aluminum screens and storm windows) with your compound miter saw . When cutting aluminum extrusions (or other sections that can be cut with a saw blade), position the material so that the blade is cutting through the smallest cross-section (Fig.
16 CUTTING CROWN MOULDING One of the many features of a compound miter saw is the ease of cutting crown molding. NOTE: The following procedur e for inside or outside crown molding corners is the same with the exception that the bevel position will always be at 30° and the miter position will be 35-1/4° to the right or left.
17 STORAGE BLADE CHANGING WRENCH STORAGE Y ou can store the blade changing wrench (A) Fig. 47 in the slot (B) behind the fence (C). Fig. 47 LOCKING CUTTINGHEAD IN THE DOWN POSITION Fig. 48 When transporting the saw , lock the cuttinghead in the down position.
1. Remove the screw (A) Fig. 50 and r otate the cover (B) to the rear (Fig. 51). 2. Depress the arbor lock (A) Fig. 52 to lock the blade. 3. Use the supplied blade changing wrench (D) Fig. 53 to loosen (clockwise) the arbor screw (E). 4. Remove the arbor screw (E), the outside the blade flange (F), and the saw blade (G) from the saw arbor .
19 Fig. 55 Fig. 56 2. The brushes are located in two holders (C) Fig. 55. Remove the spade type terminal connectors (D) and pull the brush holders (C) out.
20 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations.
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas registradas de POR TER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.
An important point after buying a device Delta 36-585 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Delta 36-585 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Delta 36-585 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Delta 36-585 you will learn all the available features of the product, as well as information on its operation. The information that you get Delta 36-585 will certainly help you make a decision on the purchase.
If you already are a holder of Delta 36-585, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Delta 36-585.
However, one of the most important roles played by the user manual is to help in solving problems with Delta 36-585. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Delta 36-585 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
