Instruction/ maintenance manual of the product 34-555 Delta
Go to page of 16
INSTRUCTION MANUAL Sliding T able Attachment (Model 34-555) P ART NO. 1346924 - 09-18-03 Copyright © 2003 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 W oodworking can be dangerous if safe and pr oper operating procedur es ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possibility of personal injury .
3 1. FOR YOUR OWN SAFETY , READ THE INSTRUCT - TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. USE CERTIFIED SAFETY EQUIPMENT .
4 FOREWORD Delta Model 34-555 Sliding T able Attachment is an accessory for providing support for large capacity wood-working operations. The fence can be positioned in the front or r ear of the movable table and can be positioned to make miter cuts. The adjustable stock stop is excellent for repetitive cutting.
5 ASSEMBL Y If your saw is equipped with the Delta Jet-Lock Rip Fence with round guide rails, cut 5-1/2" of f of the left end of both the front and r ear guide rails. If your saw is equipped with a Beisemeyer fence, measur e 1-1/2" to the left from the left side of the table and cut the rail.
6 FOR 10" CONTRACTOR’S SA WS (CURRENT STYLE) Fig. 9 Fig. 10 1. If your switch is attached to the left extension wing, remove it. (After installation of the sliding table, r e-attach the switch to the location shown in Fig. 9.) 2. Remove the left-hand table extension.
7 Fig. 15 Fig. 16 FOR 10" TIL TING ARBOR SA WS ONL Y 1. Remove the motor cover . (T o use the Sliding table, replace the motor cover with the part #734557 Hinged Motor Cover . Refer to the instructions that accompany the cover for installation.) 2.
1. Attach the upper rail assembly (L) Fig. 27 to the side of the table where the extension wing was pr eviously mounted, using the three 2-1/2" socket head scr ews (M) and lockwashers (N) thr ough the holes (C) Fig.
9 9 Fig. 27 Fig. 28 Fig. 29 Fig. 30 Fig. 31 L M N C E B D A R Q Q P S P W U T S V Fig. 32 Fig. 33 Fig. 34 P S X S E Z A Y F Fig. 35 Fig. 36 E F B D C C H G Fig. 37 F Y J Fig. 38 K M L For Old Contractor’ s Saws, turn bracket (A) Fig. 34 upside down so that the bearing (Y) contacts the rail (F).
10 Fig. 43 Fig. 44 F G H F G Fig. 39 Fig. 40 Fig. 41 Fig. 42 N P R V S N P R X Y W C D E C E NOTE: Never operate the sliding table with the table lock/stop bracket removed.
11 H C A B Fig. 50 Fig. 51 Fig. 52 Fig. 53 Fig. 54 A B C A B C F G E D K F G E H J M L ADJUSTING HEIGHT OF RIGHT EDGE OF SLIDING T ABLE L The right edge of the sliding table should be slightly higher than the machine table, both front and r ear . T o check and adjust: 1.
Adjust the sliding table so that it is parallel with the machine table. (The sliding table must also be slightly higher than the machine table.) T o check and adjust: Fig. 56 Fig. 57 A B C E F D ADJUSTING SLIDING T ABLE P ARALLEL WITH MACHINE T ABLE L 12 1.
13 Fig. 66 Fig. 64 Fig. 65 A Fig. 58 Fig. 59 A Fig. 60 Fig. 61 Fig. 62 Fig. 63 B B E C D A G F H Fig. 67 K L J N M.
14 14 Fig. 68 1. Loosen the clamp handle (A) and the clamp knob (D) Fig. 68. Slide the fence (C) Fig. 68 from the two fence clamps (B). 2. Remove the fence locking handle, the clamp knob, and the fence clamps (B) and re-position the fence clamps (B), clamp handle, and clamp knob to the rear of the sliding table (Fig.
15 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standar ds and are serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations.
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.
An important point after buying a device Delta 34-555 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Delta 34-555 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Delta 34-555 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Delta 34-555 you will learn all the available features of the product, as well as information on its operation. The information that you get Delta 34-555 will certainly help you make a decision on the purchase.
If you already are a holder of Delta 34-555, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Delta 34-555.
However, one of the most important roles played by the user manual is to help in solving problems with Delta 34-555. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Delta 34-555 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
