Instruction/ maintenance manual of the product 3 H.P. SINGLE-STAGE DUST COLLECTOR 50-852 Delta
Go to page of 16
INSTRUCTION MANUAL 3 H.P . Single-Stage Dust Collector (Model 50-852, thr ee phase) (Model 50-853, single phase) P ART NO. 902108 - 06-27-02 Copyright © 2002 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the product. Using the machine with r espect and caution will considerably lessen the possibility of personal injury .
3 ADDITIONAL SAFETY RULES FOR DUST COLLECTORS WARNING: F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJURY . 1. DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions.
4 UNP ACKING AND CLEANING Carefully unpack the tool and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened wi th ke r osene (do not use acetone, gasoline or lacquer thinner for this purpose).
5 Fig. 5 Fig. 6 Fig. 7 Fig. 8 ASSEMBLING CASTER ASSEMBLIES TO BASE Align the holes in caster assembly (A) Fig. 5, with four holes in support stand (B) located on the underside of base (C). Place a lockwasher (E) Fig. 5 onto a hex head screw (D), insert the hex head scr ew through the caster (A), and thread into hole in base (B).
6 Fig. 9 Fig. 10 Fig. 11 Fig. 12 4. Apply a bead of silicone sealant around flange of chute (F) Fig. 9. Align holes in ten-hole gasket (G) Fig. 9, with mounting holes in blower flange (F) and press gasket onto flange as shown. 5. Align mounting holes in dust chute (H) Fig.
7 Fig. 13 Fig. 14 Fig. 15 Fig. 17 7. Apply a bead of silicone sealant around flange of chute (H) Fig. 14. Align holes in eight-hole gasket (K) Fig. 14, with mounting holes in chute (H) and press gasket (K) onto flange as shown. 8. Align mounting holes in left hand drum (N) Fig.
8 Fig. 18 Fig. 19 Fig. 21 Fig. 20 11. Align two mounting holes in the top of drum support arm (T) Fig. 18, with two pre-drilled holes in drum (N) and fasten drum support arm (T) to drum (N).
9 Fig. 22 Fig. 23 Fig. 24 Fig. 25 ASSEMBLING FIL TER AND DUST COLLECTION BAGS TO DRUM 1. Hook the loop on the top of filter bag (A) Fig. 22, onto filter bag support rod (B) as shown. 2. Assemble extension rod (C) Fig. 23, into the end of filter bag support rod (B).
10 Fig. 26 Fig. 28 4. Pull up on each retaining clip (A) Fig. 26, and insert the dust collection bag (B) underneath each retaining clip to hold the dust collection bag in place. 5. Place the locking clamp (C) Fig. 26 around dust collection bag and dust collector drum and lock in place.
11 Fig. 29 Fig. 30 Fig. 31 ASSEMBLING DUST INT AKE POR T TO BLOWER AND MOTOR ASSEMBL Y MAKE CERT AIN THE DUST COLLECTOR IS DISCONNECTED FROM THE POWER SOURCE . 1. Align the four holes in the dust intake port (A) Fig. 29, with the mounting holes in the lip of flange (B) of blower assembly and fasten with four sheet metal screws (C).
12 Fig. 32 Fig. 33 Fig. 34 Fig. 35 MODEL 50-853 SINGLE PHASE INST ALLA TION Y our dust collector is supplied with a motor and controller; however , it is not supplied with a power cord and plug. 1. T o connect the dust collector to a power system, remove contr oller cover (A) Fig.
13 OPERA TING CONTROLS ON/OFF SWITCH (Model 50-852) The “on/off” switch is located on the side of the motor stand. T o tur n the dust collector “ON”, push button (A) Fig. 36. T o tur n the dust collector “OFF”, push button (B). Fig. 36 Fig.
14 NOTES.
15 Printed in U.S.A. P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable · Delta Factory Service Centers and Delta Authorized Service Stations.
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.
An important point after buying a device Delta 3 H.P. SINGLE-STAGE DUST COLLECTOR 50-852 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Delta 3 H.P. SINGLE-STAGE DUST COLLECTOR 50-852 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Delta 3 H.P. SINGLE-STAGE DUST COLLECTOR 50-852 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Delta 3 H.P. SINGLE-STAGE DUST COLLECTOR 50-852 you will learn all the available features of the product, as well as information on its operation. The information that you get Delta 3 H.P. SINGLE-STAGE DUST COLLECTOR 50-852 will certainly help you make a decision on the purchase.
If you already are a holder of Delta 3 H.P. SINGLE-STAGE DUST COLLECTOR 50-852, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Delta 3 H.P. SINGLE-STAGE DUST COLLECTOR 50-852.
However, one of the most important roles played by the user manual is to help in solving problems with Delta 3 H.P. SINGLE-STAGE DUST COLLECTOR 50-852. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Delta 3 H.P. SINGLE-STAGE DUST COLLECTOR 50-852 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
