Instruction/ maintenance manual of the product 4688513 Dell
Go to page of 38
Dell™U 3011 Flat Panel Monitor User's Guide Notes, Caution s, and Warning s Information in this document is subject to change without notice. © 2010DellInc.Allrightsreserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.
Back to Contents Page About Your Monitor Dell™U3011FlatPanelMonitorUser'sGuide Package Contents Your monitor ships with the components shown below. Ensure that you have received all the components and contact Dell if something is missing.
Product Features The U3011 flat panel display has an active matrix, thin - film transistor (TFT), liquid crystal display (LCD). The monitor features include: ■ 756.23 mm (30 inches) viewable area display (measured diagonally). ■ 2560 x 1600 resolution, plus full - screen support for lower resolutions.
Back View Side View 3 Shortcut Key 3 - Input Source (Default) 4 Menu 5 Exit 6 Power (with power light indicator) NOTE: 1~5 are capacitive touch sensor keys, which are activated by placing your finger on the blue LED.
Bottom View Monitor Specifications Flat Panel Specifications Bottom view Bottom view with monitor stand Label Description Use 1 AC power cord connector Connect the power cable . 2 DC power connector for Dell Soundbar Connect the power cord for the soundbar (optional) .
*U3011 color gamut (typical) is based on CIE1976 ( 117% ) and CIE1931 (102%) test standards. Resolution Specifications Analog signal input Digital signal Input (DVI dual link and DisplayPort and HDMI) Supported Video Modes Preset Display Modes Electrical Specifications Color depth 1.
Physical Characteristics Environmental Characteristics sync(H+V) 0.3 volt, 75 ohm input impedance Synchronization input signals Separate horizontal and vertical synchronizations, polarity - free TTL level, SOG (Composite SYNC on green) AC input voltage/frequency/current 100 to 240 VAC / 50 Hz/60 Hz +/ - 3 Hz / 2.
Power Management Modes IfyouhaveVESA'sDPM™compliancedisplaycardorsoftwareinstalledinyourPC,themonitorcanautomaticallyreduceitspowerconsumptionwhennotin use. This is referred to as Power Save Mode *.
DVIConnector 20 - pinDisplayPortConnector 12 DDC - SDA 13 H- sync 14 V- sync 15 DDC - SCL NOTE: Pin 1 is at the top left. Pin Number 24 - pin Side of the Connected Signal Cable 1 T.M.D.S. Data 2 - 2 T.M.D.S. Data 2+ 3 T.
19 - pinHDMIConnector Component Video Connector 5 GND 6 ML1(n) 7 ML2(p) 8 GND 9 ML2(n) 10 ML3(p) 11 GND 12 ML3(n) 13 GND 14 GND 15 AUX(p) 16 GND 17 AUX(n) 18 HPD 19 DP_PWR Return 20 +3.
Universal Serial Bus (USB) Interface USB Upstream C onnector USB Downstream C onnector USB P orts l 1 upstream - back l 4 downstream - 2 on back; 2 on left side Plug and Play Capability You can install the monitor in any Plug and Play - compatible system.
Identification Data (EDID) using Display Data Channel (DDC) protocols so the system can configure itself and optimize the monitor settings. Most monitor installations are automatic; you can select different settings if desired. For more information about changing the monitor settings, see Operating the Monitor .
For best practices, follow the instructions in the list below while unpacking, cleaning, or handling your monitor: l To clean your antistatic screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen - cleaning tissue or solution suitable for the antistatic coating.
Back to Contents Page Appendix Dell™U3011FlatPanelMonitorUser'sGuide Safety Instructions FCC Notice (U.S. Only) and Other Regulatory Information Contacting Dell WARNING: Safety Instructions For information on safety instructions, see the Product Information Guide .
Back to Contents Page Setting Up Your Monitor Dell™U3011FlatPanelMonitor IfyouhaveaDell™desktoporaDell™portablecomputerwithinternetaccess 1. Go to http://support.dell.com , enteryourservicetag,anddownloadthelatestdriverforyourgraphicscard.
Back to Contents Page Setting Up Your Monitor Dell™U3011FlatPanelMonitor IfyouhaveanonDell™desktop,portablecomputer,orgraphicscard In Windows XP: 1. Right - click on the desktop and click Properties .
Back to Contents Page Operating the Monitor Dell™U3011FlatPanelMonitorUser'sGuide Using the Front Panel Controls Using the On - Screen Display (OSD) Menu.
Using the On - Screen Display (OSD) Menu Accessing the Menu System 1. Touch the button to launch the OSD menu and display the main menu. Main Menu for analog (VGA) Input 2. Touch the or button to move between the setting options. As you move from one icon to another, the option name is highlighted.
Brightness / Contrast Use this menu to activate Brightness/Contrast adjustment. Brightness Brightness adjusts the luminance of the backlight. Touch the button to increase brightness and touch the button to decrease brightness (min 0 ~ max 100).
HDMI Select HDMI input when you are using the HDMI connector. Touch the button to select the HDMI input source. Component Select Component input when you are using the Component connector. Touch the button to select the Component input source. Color Setting s Use the Color Settings to adjust the color setting mode and color temperature.
Preset Modes You can choose Standard, Multimedia, Game, Movie, Warm, Cool, Adobe RGB, sRGB, xv Mode or Custom Color; l Standard : Loads the color settings suitable for desktop applications . This is the default preset mode. l Multimedia : Loads color settings suitable for multimedia applications , e.
Display Settings Use the Display Settings to adjust image. Wide Mode Adjust the image ratio as 16:9, 4:3, 1:1, Aspect or full screen. Horizontal Position Use the or to adjust image left or right. Minimum is '0' ( - ). Maximum is '100' (+).
NOTE: Line Out Source selection is available only when the monitor display is in PBP mode. Audio Configurations Audio offers two kind of configurations of audio channels. Use the or to move between 2 channels and 5.1 channels and select the desired option.
PBP Mode To turn on or off Picture by Picture (PBP) . PBP Source Select an input signal for Picture by Picture (PBP). (HDMI 1/HDMI 2/Component).
OSD Warning Messages LCD Conditioning Helps reduce minor cases of image retention. Depending on the degree of image retention, the program may take some time to run. You can enable this feature by selecting "Enable". Factory Reset ResetallOSDsettingstothefactorypresetvalues.
When the monitor does not support a particular resolution mode you will see the following message: This means that the monitor cannot synchronize with the signal that it is receiving from the computer. See Monitor Specifications for the HorizontalandVerticalfrequencyrangesaddressablebythismonitor.
See Solving Problems for more information. Setting the Maximum Resolution To set the Maximum resolution for the monitor: Windows XP: 1. Right - click on the desktop and select Properties .
Using the Tilt, Swivel, and Vertical Extension Tilt , Swivel With this stand, you can tilt and swivel the monitor for the most comfortable viewing angle. Vertical Extension 1. Attach mechanism 2. Headphone jacks 3. Power indicator 4. Power/Volume control NOTE: This is applicable for a monitor with a stand.
.
Back to Contents Page Setting Up Your Monitor Dell™U3011FlatPanelMonitor Setting the display resolution to 2048 x 1280 (VGA input source) / 2560 x 1600 (DVI/DisplayPort™inputs.
Dell™U 3011 FlatPanelMonitor Information in this document is subject to change without notice. © 2010DellInc.Allrightsreserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.
Back to Contents Page Setting Up the Monitor Dell™U3011FlatPanelMonitorUser'sGuide Connecting the Monitor Organizing Your Cables Attaching the Soundbar (optional) Removing the Stand Attaching the Stand Connecting the Monitor To connect your monitor to the computer: 1.
After you have completed connecting the DVI/VGA /DisplayPort cable, follow the procedure below to complete your monitor setup: 1. Plugthepowercablesforyourcomputerandmonitorintoanearbyoutlet. 2. Turn on the monitor and the computer.
Removing the Stand To remove the stand: 1. Place the monitor on a flat surface. 2. Remove the four screws from the stand. 3. Lift the stand up and away from the monitor. Attaching the Stand To attach the monitor stand: 1. Place the monitor on a flat surface.
Back to Contents Page Troubleshooting Dell™U3011FlatPanelMonitorUser'sGuide Self - Test Built - in Diagnostics Common Problems Product Specific.
To run the built - in diagnostics: 1. Ensure that the screen is clean (no dust particles on the surface of the screen). 2. Unplug the video cable(s) from the back of the computer or monitor. The monitor then goes into the self - test mode. 3. Press and hold the Button 1 and Button 4 on the front panel simultaneously for 2 seconds.
Product Specific Problems Universal Serial Bus (USB) Specific Problems NOTE: When using DVI - D input, the positioning adjustments are not available. Horizontal/Vertical Lines Screen has one or more lines l Reset the monitor to Factory Settings. l Perform Auto Adjust via OSD.
Dell™Soundbar Problems Back to Contents Page High Speed USB 2.0 interface is slow. High Speed USB 2.0 peripherals working slowly or not working at all l Check that your computer is USB 2.0 - capable. l Some computers have both USB 2.0 and USB 1.1 ports.
An important point after buying a device Dell 4688513 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dell 4688513 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dell 4688513 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dell 4688513 you will learn all the available features of the product, as well as information on its operation. The information that you get Dell 4688513 will certainly help you make a decision on the purchase.
If you already are a holder of Dell 4688513, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dell 4688513.
However, one of the most important roles played by the user manual is to help in solving problems with Dell 4688513. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dell 4688513 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
