Instruction/ maintenance manual of the product INTERCOM AN-8000 Aiphone
Go to page of 10
N E TWO RK IN T ERCO M SYSTE M A N -8 0 0 0 S E R I E S Quickstart Guide Thank you for purchas ing AIPHON E's Network Interco m s y stem . Please caref ully follow the instruc tions in this m anual t o ensure long, tr ouble-f ree use of your equipm ent.
.
AN Quickstart Guide Overview Network Design Setup a network your system will use to communicate between devices System Name The first (and critical) step in editing an exis ting system or designing a .
Unit Scan Unit Scan is used to make IP address assignments to the hardware. With the Unit Scan window open click the Scan button. When the equipment list appears, double click each address and change it to match what you were given by the network administrator and press enter to save each setting.
Station Table The Station Table is the tab that allows us to assign extensions to allow the end user to dial between equip ment. Switch to the Station Table tab and fill out the blank column Station Number for each device. If you need more than 2 digits, change the Station No.
Note: If there is a p roblem you can try pointing your b rowser to the IP address of the station and attempt to log in. See the Troubleshooting the Network section for additional d etails. To test your system a fter all devices have successfu lly been uploaded to, press th e call button on each door and see if the correct master rings.
Example: In Figu re 13, we split the system into 2 groups, with a door and a master in each group . Figure 14 gives access for each group, and for each pag ing zone. Put a check box in the column for ea ch group you want that column to have access to.
Figure 14: Group Blocking to, set ting permissions. See page 193 of the AN guide. Note: In the example MI configuration, we are se tting up audio channel 1 for a BGM source and channel 2 for a PBX connection.
Note: Power over Ether net is the preferred way to power AN-8540DS IP door stations or AN-8500MS IP master stations, alth ough you can buy a select few plug in transformers if PoE is not availa ble. Use a 12VDC power supp ly with a 2.1mm x 5.5mm barrel conne ctor.
screenshots it is still “New System” which means an upload has not been attempted and the default syste m name and password should still work, assuming of course no one else has attempted to upload settings t o that device.
An important point after buying a device Aiphone INTERCOM AN-8000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Aiphone INTERCOM AN-8000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Aiphone INTERCOM AN-8000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Aiphone INTERCOM AN-8000 you will learn all the available features of the product, as well as information on its operation. The information that you get Aiphone INTERCOM AN-8000 will certainly help you make a decision on the purchase.
If you already are a holder of Aiphone INTERCOM AN-8000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Aiphone INTERCOM AN-8000.
However, one of the most important roles played by the user manual is to help in solving problems with Aiphone INTERCOM AN-8000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Aiphone INTERCOM AN-8000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
