Instruction/ maintenance manual of the product Advantage Electrol Da-Lite
Go to page of 8
DA-LITE SCREEN COMP ANY , INC. 3100 North Detroit Street Post Office Box 137 Warsaw , Indiana 46581-0137 Phone: 574-267-8101 800-622-3737 Fax: 574-267-7804 T oll Free Fax: 877-325-4832 www .da-lite.com e-mail: info@da-lite.com Instruc tion Book for A D V A N T AG E ® E L E C T R O L ® T h e D a - L i t e D i f f e r e n c e .
If your screen w as shipped with the motor and roller already inst alled, proceed to step 6. 1 . Remo ve access door . First, remo v e the 2 screws from the ends. B e sure to support the door during this step to av oid injur y . Then lif t the door slightly and pull a wa y from the edge of the case.
2 ADV ANT AGE ® ELECTROL ® INST ALLA TION FOR 120V SCREENS UP OFF DO WN THIS SWITCH CAN NO T BE USED WITH L V C. 120V WIRING DIAGRAM FOR ST ANDARD W ALL SWITCH SPDT SWITCH WITH CENTER OFF A C (COMMO.
LOW-VOL TAGE W ALL SWITCH OPTIONAL IR AND RF REMOTE CONTROL MOTOR BLUE (COMMON) BROWN (HOT) GREEN GROUND TO CASE 240VAC 50HZ 240V WIRING DIAGRAM WITH OPTIONAL BUIL T -IN LOW VOL T AGE CONTROL RJ9 UP S.
Surface tra vel is stopped automatically in the fully opened and closed positions by limit switc hes that are properly adjusted at Da-Lite. Should it be necessar y to adjust for more or less drop of pict ure, proceed in the following manner: Remo ve two screws to remo ve access door .
5 SCREEN ADJUSTMENT FOR 120V SCREENS WITH A BUIL T -IN LOW VOL T AGE CONTROL 1 . Remo ve the cov er plate from the 3-but ton wall switc h and remov e the switc h from the junction box. 2. Locate small 3-position switc h on bac k of w all switc h. See Figure 5 for 1 20V screens or Figure 8 for 220/240V screens.
6 ADV ANT AGE ® ELECTROL ® INST ALLA TION 7-3/4" 6-1/16" 3/8" THREADED ROD (NOT INCLUDED) A TTACHED TO MOUNTING BRACKET SELF-TRIMMING FLANGE 6-3/8" 7-3/4" FINISHED CEILING 8" 6.42" 3/8" THREADED ROD (NOT SUPPLIED) HANGER BRACKET SEE DET AIL A 7.
Printed in U .S.A. 8421 4 Rev . 12/09 7 TROUBLESHOOTING SYMPTOM 1 . Screen will not operate. Motor does not hum. 2. Screen does not stop at correct position. 3. Noise. NOTE: Screen will operate with a low-pitched hum. 4. Coasting . 5. Fabric hangs crooked.
An important point after buying a device Da-Lite Advantage Electrol (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Da-Lite Advantage Electrol yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Da-Lite Advantage Electrol - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Da-Lite Advantage Electrol you will learn all the available features of the product, as well as information on its operation. The information that you get Da-Lite Advantage Electrol will certainly help you make a decision on the purchase.
If you already are a holder of Da-Lite Advantage Electrol, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Da-Lite Advantage Electrol.
However, one of the most important roles played by the user manual is to help in solving problems with Da-Lite Advantage Electrol. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Da-Lite Advantage Electrol along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
