Instruction/ maintenance manual of the product CY7C68300C Cypress Semiconductor
Go to page of 42
EZ-USB A T2LP™ USB 2.0 to A T A/A T API Bridge CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Cypress Semiconductor Corpora tion • 198 Champion Cou rt • San Jose , CA 95134-1 709 • 408-943-2 600 Document 001-05809 Rev .
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 2 of 42 Applications The CY7C68300C/30 1C and CY7C68320C/321A impleme nt a USB 2.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 3 of 42 Pin Diagrams The A T2LP is available in different package types to meet a va riety of design needs. The C Y7C68320C/321C is availab le in 56-pin QFN and 100-pin TQFP packages to provide the greatest flexibi lity for new designs.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 4 of 42 Figure 3. 56-pin QFN Pinout (CY7C68300C/CY7C683 01C) RESET# GND ARESET# DA2 ( VBUS_PWR_VAL ID ) CS1# CS0# DRVPW RVL.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 5 of 42 Figure 4. 56-pin SSOP Pinout (CY7C68320C/CY7C683 21C) 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 .
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 6 of 42 Figure 5. 56-pin QFN Pinout (CY7C68320C/CY7C683 21C) GND VCC GPIO2 GND DD15 DD14 DD13 DD12 DD11 DD10 DD9 DD8 VBUS_A.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 7 of 42 Figure 6. 100-pin T QFP Pinout (CY7C68320C/CY7C68321 C only) 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 8 of 42 Pin Descriptions The following table lists the pinouts for the 56-pin SSOP , 56-pin QFN and 100-pin T QFP package options for th e A T2LP .
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 9 of 42 30 16 23 SDA IO Data signal for I 2 C interface. (See “SCL, SDA” on page 1 1 ). Apply a 2.2k pull up resistor . 31 32 N/A N/A NC No connect. 33 17 24 V CC PWR V CC .
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 10 of 42 68 34 41 DA0 O/Z [1] Driven HIGH after 2 ms delay A T A ad dress . 69 35 42 DA1 O/Z [1] Driven HIGH after 2 ms delay A T A ad dress . 70 [3] 36 [3] 43 DRVPWR VLD ( DA2 ) I Input Device presence dete ct.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 1 1 of 42 Additional Pi n Descriptions The following se ctions provide additional pin information. DPLUS, DMINUS DPLUS and DMINUS are the USB signali ng pins; they must be tied to the D+ and D– pins of the USB con nector .
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 12 of 42 SYSIRQ The SYSIRQ pin provides a way for systems to request service from host software by using the USB Interrupt pipe o n endpoint 1 (EP1). If the A T2LP has no pe ndi ng interrupt data to return, USB interrupt pipe data requests are NAKed.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 13 of 42 Figure 8. SYSIRQ Latching Algorithm DRVPWRVLD When this pin is e nabled with bit 0 of configuration address 0x08 (DRVPWR VLD Enable), the A T2LP informs the host that a removable device, su ch as a CF ca rd, is present.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 14 of 42 interface and the attached mass storage d evice, especially if Ultra DMA Mode is used. VBUS_A T A_ENABLE VBUS_A T A_ENABLE is typically used to indicate to the A T2LP that power is p resent on VBUS.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 15 of 42 HID Functions for Button Controls Cypress’s CY7C68320C/CY7C68321C has the capability of supporting Human Interface Device (HID ) signaling to the host.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 16 of 42 T able 6. A T ACB Field Descriptions Byte Field Name Field Descripti on 0 bVSCBSignature This field indicates to the CY7C68300C/CY7C6 8301C that the A T ACB contains a vendor-specific command blo ck.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 17 of 42 3 bmA T ACBRe gisterSele ct This field controls which of the taskfile register read or write accesses occur . T askfile read data is always 8 bytes in leng th, and unselected register data are returned as 0x00.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 18 of 42 Operating Modes The different modes of oper ation and EEPROM information are presented in the following se ctions. Operational Mode Select ion Flow During the power-up sequence, the A T2LP queries the I 2 C bus for an EEPROM.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 19 of 42 Fused Memory Data When no EEPROM is detected at startup, the A T2LP enumerates with the VI D/PID/DID values that are stored in the fused memory space.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 20 of 42 MfgCB The mfg_load and mfg _read vendor-specific commands are passed down through th e bulk pipe in the CBWCB p ortion of the CBW . The format of thi s MfgCB is shown as foll ows.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 21 of 42 EEPROM Organization The contents of the recommended 256-byte (2048-bit) I 2 C EEPROM are arranged as follows. In T able 1 1 , the column labeled ‘Required Conten ts’ contains the values that must be used for proper operation of the A T2LP .
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 22 of 42 T able 1 1.Configuration Dat a Organization Byte Address Configuration Item Name Configuration Item Description Re.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 23 of 42 SRST Enable Bit 1 Determines if th e A T2LP is to do an SR ST reset during drive initialization. At le ast one reset must be enabled. Do not set SRST to 0 and Skip Pin Rese t to 1 at the same time.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 24 of 42 0x08 BUTTON_MODE Bit 7 Button mode (100-pin package only). Sets A T APUEN, PWR500# and DRVPWRVLD to become button inputs returned on bits 2, 1, and 0 of EP1IN. This bit must be set to ‘0’ if the 56-pin packages are used.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 25 of 42 0x0A Reserved GPIO Output Pin S tate Bits 7:6 Reserved. Must be set to zero. Bits 5:0 These bits select the value driv en on the GPIO pins that are configured as outputs in configuration address 0x09.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 26 of 42 0x12 bcdUSB (LSB) USB S pecification release number in BCD 0x00 0x13 bcdUSB (MSB) 0x02 0x14 bDeviceClass Device cl.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 27 of 42 0x32 iConfiguration Index to the configu rati on string. This entry must eq ual half of the address value where the string starts, or 0x00 if the string does not e xist.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 28 of 42 0x4F bAlternateSetting Alternate setting 0x00 0x50 bNumEndpoints Number of endpoints used by this interface 0x01 0.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 29 of 42 0x75 Report_Size 8 bits 0x75 0x76 0x08 0x77 Report_Count 2 fields 0x95 0x78 0x02 0x79 Input Input (Data, V ariable.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 30 of 42 0x95 bRecipient Identifier of the target recipient If Recipient type field of bmAttributes = 1 then bRecipient fie.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 31 of 42 0xB5 bS tring Unicode character LSB ’ ’ 0x20 0xB6 bS tring Unicode character MSB 0x00 0xB7 bS tring Unicode ch.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 32 of 42 0xDF bS tring Unicode characte r LSB ’ ’ 0x20 0xE0 bS tring Unicode character MSB 0x00 0xE1 bS tring Unicode c.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 33 of 42 Note : More than 0X100 bytes of co nfiguration are shown for ex ample only .
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 34 of 42 Legal values for wV alue are as follows: • 0x0000 Internal Config bytes, address range 0x2 – 0xF • 0x0002 External I 2 C memory device Internal Config byte writes must be con strai ned to ad dresses 0x2 through 0xF , as shown in Ta b l e 1 2 .
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 35 of 42 Absolute Maximum Ratings S torage T emperature .............. ... ......................... .......................... ......................... ... ............ .. .
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 36 of 42 AC Electrical Characteristics A T A Timing C haracter istics The A T A interface supports A T A PIO modes 0, 3, and 4, Ultra DMA modes 2, 3, and 4, and mu lti-word DMA mode 2, per the A T A/A T API 6 S pecificatio n.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 37 of 42 Package Diagrams Figure 12. 100-Pin Thin Plastic Qu ad Flatp ack (14 x 20 x 1.4 mm) A101 NOTE: 1. JEDEC STD REF MS-026 2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 38 of 42 Figure 13. 56-lead Shrunk Sm all Outline Package 05 6 Package Diagrams (continued) 0.095 0.025 0.008 SEATING PLANE 0.420 0.088 .020 0.292 0.299 0.395 0.092 BSC 0.110 0.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 39 of 42 General PCB Layout Recommendations For USB Ma ss Storage Designs The following recommendation s must be followed to ensure reliable high-performance operation: • Use at least a four-layer , impedance controll ed board to maintain signal quality .
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 40 of 42 Quad Flat Package No Leads (QFN) Package Design Note s Electrical contact of the part to the Printed Circuit Board (PCB) is made by soldering the leads on the botto m surface of the package to the PCB.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 41 of 42 © Cypress Semi con duct or Cor po rati on , 20 06 . The information contained he re i n is su bj ect to ch an ge wi t hou t n otice.
CY7C68300C/CY7C68301C CY7C68320C/CY7C68321C Document 001-05809 Rev . *A Page 42 of 42 Document History Paged Description Title: CY7C68300C/CY7C68301C/CY7 C683 20C/C Y7C68321C EZ-USB A T2LP™ USB 2.0 to A T A/A T API Bridge Document Numb er: 001-05809 REV .
An important point after buying a device Cypress Semiconductor CY7C68300C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cypress Semiconductor CY7C68300C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cypress Semiconductor CY7C68300C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cypress Semiconductor CY7C68300C you will learn all the available features of the product, as well as information on its operation. The information that you get Cypress Semiconductor CY7C68300C will certainly help you make a decision on the purchase.
If you already are a holder of Cypress Semiconductor CY7C68300C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cypress Semiconductor CY7C68300C.
However, one of the most important roles played by the user manual is to help in solving problems with Cypress Semiconductor CY7C68300C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cypress Semiconductor CY7C68300C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
