Instruction/ maintenance manual of the product EZ-USB FX2 PCB Cypress
Go to page of 7
November 21, 2002 Document No. 001-431 17 Rev . ** 1 EZ-USB FX2™ PCB Design Recommendations Introduction This application n ote presents recommendati ons for design- ing with the Cypress Semiconductor EZ-USB FX2™ compo- nent. T echniques for high-speed desi gn should be applied to circuits using the EZ-USB FX2.
November 21, 2002 Document No. 001-431 17 Rev . ** 2 AN1 196 Figure 2. FX2 Eye Diagram of High-speed Signali ng In the diagram, notice how no signal traces overlap the cen- tral, six-sided, shade d area. Also, no trace overlaps the extremes of permissible volt age as shown in the shaded lin es at the very top and very bottom of the figure.
November 21, 2002 Document No. 001-431 17 Rev . ** 3 AN1 196 Maint ain PCB T race Impedance Designing the PCB traces for particular ch aracteristic imped- ance is very important to signal quality . The USB specification requires controlled impedance a mong all elements in the USB data path.
November 21, 2002 Document No. 001-431 17 Rev . ** 4 AN1 196 This figure shows the die lectric material thickness (“Prepreg”) between layers 1 and 2 and the thickness between layers 3 and 4. The dimensio ns between these layers are a key ele- ment in the design to se t the proper characteristic impedance for the USB data traces.
November 21, 2002 Document No. 001-431 17 Rev . ** 5 AN1 196 The design of the land area fo r the expose d paddle is critical to proper thermal transfer . A copper fill is to be designed into the PCB and under the QFN in order to assist thermal trans- fer .
November 21, 2002 Document No. 001-431 17 Rev . ** 6 AN1 196 EZ-USB FX2 Assembly Recommenda- tions The solder stencil over the expos ed p addle is required to per- mit at least 50% solder application coverage. Figure 8 is a graph from Amkor research showing how solder void mu ch less than 50% has little influe nce on thermal transfer .
AN1 196 Cypress Semico nd uctor 198 Champi on Cou rt San Jose, CA 9513 4-1709 Phone: 408- 943-2600 Fax: 408-94 3-4730 http://www.cypr ess.com © Cypress S emiconductor Corpora tion, 2002-2007. The information containe d herein is subjec t to change with out notice.
An important point after buying a device Cypress EZ-USB FX2 PCB (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cypress EZ-USB FX2 PCB yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cypress EZ-USB FX2 PCB - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cypress EZ-USB FX2 PCB you will learn all the available features of the product, as well as information on its operation. The information that you get Cypress EZ-USB FX2 PCB will certainly help you make a decision on the purchase.
If you already are a holder of Cypress EZ-USB FX2 PCB, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cypress EZ-USB FX2 PCB.
However, one of the most important roles played by the user manual is to help in solving problems with Cypress EZ-USB FX2 PCB. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cypress EZ-USB FX2 PCB along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
