Instruction/ maintenance manual of the product AutoStore STK17TA8 Cypress
Go to page of 23
STK17T A8 128k X 8 AutoS tore™ nvSRAM with Real T ime Clock Cypress Semiconductor Corpora tion • 198 Champion Court • San Jose , CA 95134-1709 • 408-943-2600 Document #: 001-52039 Rev .
STK17T A8 Document #: 001-52039 Rev . ** Page 2 of 23 Pinout s Figure 1. Pin Diagram - 48-PIn SSOP V SS A 14 A 12 A 7 A 6 DQ 0 DQ 1 V CC DQ 2 A 3 A 2 A 1 V CAP A 13 A 8 A 9 A 11 A 10 DQ 7 DQ 6 V SS A .
STK17T A8 Document #: 001-52039 Rev . ** Page 3 of 23 Absolute Maximum Ratings V oltage on Input Rela tive to Gr ound ................ –0.1V to 4.1V V oltage on Input Rela tive to V SS .........–0.5V to (V CC + 0.5V) V oltage on DQ 0-7 or HSB ....
STK17T A8 Document #: 001-52039 Rev . ** Page 4 of 23 AC T est Conditions Input Pulse Levels ...... ............... .............. ........... ...... 0V to 3V Input Rise and Fall T imes ........... .............. .............. ..... < 5 ns Input and Output T iming Reference Levels .
STK17T A8 Document #: 001-52039 Rev . ** Page 5 of 23 RTC DC Characteristics Figure 4. RTC Recommended Component Configuration Symbol Parameter Commercial Industrial Unit s Notes Min Max Min Max I BAK RTC Backup Current — 300 — 350 nA From either V RTC ca p or V RTC b at V RTC ba t RTC Battery Pin V oltage 1.
STK17T A8 Document #: 001-52039 Rev . ** Page 6 of 23 SRAM READ Cycles #1 and #2 Figure 5. SR AM READ Cycle #1: Address Controlled [3, 4, 6] Figure 6. SRAM READ Cycle #2: E and G Controlled [3, 6] Notes 3. W must be high during SRAM READ cycles. 4. Device is continuously selected with E and G both low 5.
STK17T A8 Document #: 001-52039 Rev . ** Page 7 of 23 SRAM WRITE Cycles #1 and #2 Figure 7. SRAM WRITE Cycle #1: W Controlled [7, 8] Figure 8. SRAM WRITE Cycle #2: E Controlled [7, 8] Notes 7. If W is low when E goes low , the outputs remain in the high-impedance state.
STK17T A8 Document #: 001-52039 Rev . ** Page 8 of 23 AutoStore/Power Up Recall Figure 9. Au toStore /Power Up RECAL L Notes 9. t HRECALL starts from the time V CC rises abov e V SWITCH 10. If an SRAM WRITE has not tak en place since the last nonvolatile cycle, no STORE will take place 1 1.
STK17T A8 Document #: 001-52039 Rev . ** Page 9 of 23 Sof tware-Controlled ST ORE/RECALL Cycle In the following table, the soft war e controlled STORE and RECALL cycle para meters are listed. [12, 13] Figure 10. Software STORE / RECALL Cycle: E CONTROLLED [13] Figure 1 1.
STK17T A8 Document #: 001-52039 Rev . ** Page 10 of 23 Hardware ST ORE Cycle Figure 12. Hardware STORE Cycle Sof t Sequence Commands Figure 13. Sof t Sequence Commands NO.
STK17T A8 Document #: 001-52039 Rev . ** Page 1 1 of 23 MODE Selection E W G A 16 -A 0 Mode I/O Power Notes H X X X Not Selected Output High Z S tandby L H L X Read SRAM Output Data Active L L X X Wri.
STK17T A8 Document #: 001-52039 Rev . ** Page 12 of 23 nvSRAM Operation The STK17T A8 nvSRAM i s made up of tw o functional compo- nents paired in the same physical cell. These are the SRAM memory cell and a nonvolatile QuantumTrap cell. The SRAM memory cell operates like a standar d fast static RAM.
STK17T A8 Document #: 001-52039 Rev . ** Page 13 of 23 atile elements. Once a STORE cycl e is initiated, further memory inputs and outp ut s are disabled until the cycle is completed. T o initiate the Software STORE cycle, the following read sequence must be performed : 1.
STK17T A8 Document #: 001-52039 Rev . ** Page 14 of 23 Figure 15. Current versus Cycle Time RTC Operations Real T ime Clock The clock registers maintain time up to 9,999 years in one second increments.
STK17T A8 Document #: 001-52039 Rev . ** Page 15 of 23 Calibrati ng The Clock The RTC is driven by a quartz controlled oscillator with a nominal frequency of 32.768 KHz. Clock accuracy will depend on the quality of the crystal, specified (usually 35 ppm at 25 C).
STK17T A8 Document #: 001-52039 Rev . ** Page 16 of 23 Interrupt s The STK17T A8 has a Flags register , Interrupt Register , and interrupt logic that can interrupt a microcontroller o r generate a power-up master reset sig nal. There are three potenti al interrupt sources: the watchd og timer , the power monitor , and the clock alarm.
STK17T A8 Document #: 001-52039 Rev . ** Page 17 of 23 RTC Register * A binary value, not a BCD value. 0 - Not implemented, reserved for future use. Default Settings of nonvolatile Calibrat ion and In.
STK17T A8 Document #: 001-52039 Rev . ** Page 18 of 23 Register Map Det ail 0x1FFFF Real Time Clock – Y ea rs D7 D6 D5 D4 D3 D2 D1 D0 10s Y ears Y ears Contains the lower two BCD digits of the year . Lower nibb le contains the value for years; up per nibble contains the value for 10s of years.
STK17T A8 Document #: 001-52039 Rev . ** Page 19 of 23 0x1FFF7 Watchdo g Timer D7 D6 D5 D4 D3 D2 D1 D0 WDS WDW WDT WDS W atchdog S trobe. Setting this bit to 1 reloads and restarts the watchdog timer . The bit is cleared automatically once the watchdog timer is reset.
STK17T A8 Document #: 001-52039 Rev . ** Page 20 of 23 0x1FFF2 Alarm – Seconds D7 D6 D5 D4 D3 D2 D1 D0 M 10s Alarm Seconds Alarm Seconds Contains the alarm value for the seconds and the ma sk bit to select or desel ect the seconds’ value. M Match.
STK17T A8 Document #: 001-52039 Rev . ** Page 21 of 23 Ordering Information Ordering Codes Packing Option Blank=T ube TR=T ape and Reel T emperatu re Range Blank=Commercial (0 to +70 C) I= Industrial .
STK17T A8 Document #: 001-52039 Rev . ** Page 22 of 23 Package Diagrams Figure 17. 48-Pin SSOP (51-85061) 51-85061 *C [+] Feedback.
Document #: 001-52039 Rev . ** Revised Ma rch 02, 2009 Page 23 of 23 AutoS tore and Qu antumT rap are re gistered trademarks of C ypress Semiconducto r Corporation. All product s and compa ny names mentio ned in this document are the trad emarks of th eir respect ive holders.
An important point after buying a device Cypress AutoStore STK17TA8 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cypress AutoStore STK17TA8 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cypress AutoStore STK17TA8 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cypress AutoStore STK17TA8 you will learn all the available features of the product, as well as information on its operation. The information that you get Cypress AutoStore STK17TA8 will certainly help you make a decision on the purchase.
If you already are a holder of Cypress AutoStore STK17TA8, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cypress AutoStore STK17TA8.
However, one of the most important roles played by the user manual is to help in solving problems with Cypress AutoStore STK17TA8. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cypress AutoStore STK17TA8 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
