Instruction/ maintenance manual of the product TN-4003 Crimestopper Security Products
Go to page of 12
Installation Instructions TRACKNET ™ TN - 4003 /4004.
2 TABLE OF CONTENTS TABLE OF CONTENTS Introduction .............................................. ............................................................. .. ....................... 2 Installation Caution and Warnings .......... .................
3 INSTALLATION CAUTIONS & WARNINGS BEFORE BEGINNING , check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, ENGINE COMPUTER S, and BATTERY etc.). WE RECOMMEND the use of a VOLT/OHM METER to test and verify wiring circuits.
4 CONTROL MODULE & COMPONENT MOUNTING Main Unit: The TrakNet unit has an internal power management program that monitors the vehicle power at all times. The internal power management program is continuously looking at the condition of the battery in order to detect the state of the vehicle operation.
5 MOUNTING LOCATION Selecting the Antenna Locations The Module requires two antennas elements. One antenna is for receivin g GPS signals from The Navistar GPS satellites. The second antenna is a radio trans ceiver antenna that communicates with the Cellular network.
6 INSTALLATION Locating Vehicle Power The TRAKNET has an internal power management program that monitors the vehi cle power at all times. The internal power management program is continuously looking at the condition of the vehicle battery in order to detect the state of the vehicle operation.
7 INSTALLATION Within five minutes the flash rate will change to approximately one second on and one second off to indicate that the GPS Receiver has established a location “lock”. Within 1 minute the flash color should be green to indicate good cellular coverage.
8 LED STATUS INDICATOR LED Status Indicator BI - COLOR ON BOARD LED: This unit has a bi - colored LED on unit. SOLID LED C OLOR: Solid Green – Device is in Test Mode: no inputs are currently being triggered. Solid Orange – Device is in Test Mode: At least one input is currently being triggered.
9 WIRING NOTE: Some Options Need to Be Pre - programmed From Crime s topper prior to installing the unit. Pin 1 Black: Chassis Ground Input THIS WIRE MUST BE CONNECTED TO TH E CHASSIS METAL OF THE VEHICLE. Scrape away any paint or dirt to ensure a good connection.
10 WIRING Pin 12 Orange: Alarm Trigger ( -) Default * or Door Open/Close Input #1 A. Alarm Trigger * : Triggers a larm input of tracking device if received a nega tive input for 15 seconds or longer. This is connected to the negative siren output , if alarm has positive siren output use a relay to convert to negative .
11 WIRING DIAGRAM.
ACCESS INFORMATION Cong ratulations, you have just installed the Internet based vehicle telematics system. Now that it’s installed, here’s how to use your system. Step #1 First fill out your TrakNet registration form and fax to 805.581 - 9500. Then you will receive a call or emai l with your login and password.
An important point after buying a device Crimestopper Security Products TN-4003 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Crimestopper Security Products TN-4003 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Crimestopper Security Products TN-4003 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Crimestopper Security Products TN-4003 you will learn all the available features of the product, as well as information on its operation. The information that you get Crimestopper Security Products TN-4003 will certainly help you make a decision on the purchase.
If you already are a holder of Crimestopper Security Products TN-4003, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Crimestopper Security Products TN-4003.
However, one of the most important roles played by the user manual is to help in solving problems with Crimestopper Security Products TN-4003. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Crimestopper Security Products TN-4003 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
