Instruction/ maintenance manual of the product RS800 Series II Crimestopper Security Products
Go to page of 12
RS800 Series II Remote Engine Starting System INSTALLATION INSTRUCTIONS PRE - INSTALLATION CONSIDERATIONS To ease and reduce installation time, we suggest you READ THIS MANUAL and consider the followi.
INSTALLATION CAUTIONS & WARNINGS **FOR SAFETY REASONS, DO NOT INSTALL THE RS800 Series II in vehicles with MANUAL TRANSMISSIONS .** If accidentally left in gear, a remote started vehicle could become a self - propelled threat to life and property.
WIRING INSTRUCTIONS YELLOW / YELLOW/WHITE ( - ) IGN. & ( - ) ACC. OUTPUTS (GROUND WHEN RUNNING): YELLOW 85 86 30 87 2nd IGN (If needed) IGN SW. OR ANTI-THEFT/ MODULE +12V CONSTANT OR TRANSPONDER PIN 4: YELLOW/BLACK: ( - ) ANTI - GRIND/STARTER KILL OUTPUT (OPTIONAL) Use this wire for the negative side of the Anti - Grind/Starter Disable relay.
WIRING INSTRUCTIONS PIN 5: EM PTY (NOT USED) PIN 6: GREEN: INSTANT START ACTIVATION BY NEGATIVE ( - ) TRIGGER INPUT This wire allows the Auxiliary Channel Output of a separate (host) Alarm or Keyless Entry System to activate a Remote Start. This wire can be used for the optional CS400 Cool Start Timed/Temperature controlled interface.
IGNITION SWITCH WIRING 6 PIN HIGH - CURRENT CONNECTORS: PIN 1: BROWN 14 GA.: S TARTER OUTPUT (30A) PIN 2: GRAY 14 GA.: ACCESSORY / IGNITION 2 (30A) PIN 3: RED 14 GA.: BATTERY CONSTANT FUSED (30A) PIN 4: RED 14 GA.: BATTERY CONSTANT FUSED (30A) PIN 5: PINK 14 GA.
POWER DOOR LOCK WIRING 3 PIN DOOR LOCK PLUG: PIN 1: GREEN: ( - ) Negative pulse for LOCK PIN 2: RED: +12V Coil Power for external relays TERM 86. PIN 3: BLUE: ( - ) Negative pulse for UNLOCK DETERMINING DOOR LOCK TYPE: We recommend determining the type of locking system the vehicle has before connecting any wires.
POWER DOOR LOCK WIRING AFTERMARKET MOTOR/DOOR LOCK WIRING REVERSE POLARITY DOOR LOCK WIRING GREEN GREEN FUSED FUSED RED RED +12V +12V BLUE BLUE + + 86 85 86 85 86 85 86 85 87 87 87 87 30 87A 30 87A 30.
TACH (RPM) REFER ENCE MODE / TACH FINDER MODE / TACH PROGRAMMING Tach Reference Mode provides reliable remote starting performance though engine speed sensing. When using Tach Reference Mode, the Red/White wire is used for Tach signal [Engine RPM] input.
TACH (RPM) REFERENCE MODE / TACH FINDER MODE / TACH PROGRAMMING NOTE (1): The Tach Signal locations on page 9 are provided as a guide, your vehicle may differ. Some locations will NOT be a good location for Tach source due to RF noise or Computer Data.
OPTION PROGRAMMING T his system has several installer programmable features as listed in the chart below. Option Programming: 1. Open hood (Ground the Gray wire if no hood pin is installed). 2. Turn Key to the ON position 3. Press program button 5 times, after a few seconds the unit w ill flash the lights 5 times.
REMOTE START TROUBLESH OOTING UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START: The unit is in Valet mode. Turn IGN ON, press and hold valet/programming button for about 4 seconds until LED goes out. The unit is now out of valet mode and should perform a remote start.
TRANSMISSION PROGRAM/ OVERRIDE PARKING LIGHTS SWITCH ECU RS-800ER ANTENNA/ RECEIVER PLUG LED COIL + - (-) UNLOCK OUTPUT +12 V FOR RELAYS 12A MAX. (-) LOCK OUTPUT ENGINE ECU GREEN BLUE RED WHITE FUEL P.
An important point after buying a device Crimestopper Security Products RS800 Series II (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Crimestopper Security Products RS800 Series II yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Crimestopper Security Products RS800 Series II - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Crimestopper Security Products RS800 Series II you will learn all the available features of the product, as well as information on its operation. The information that you get Crimestopper Security Products RS800 Series II will certainly help you make a decision on the purchase.
If you already are a holder of Crimestopper Security Products RS800 Series II, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Crimestopper Security Products RS800 Series II.
However, one of the most important roles played by the user manual is to help in solving problems with Crimestopper Security Products RS800 Series II. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Crimestopper Security Products RS800 Series II along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
