Instruction/ maintenance manual of the product CS-882 Crimestopper Security Products
Go to page of 10
CS - 882 OEM ALARM UPGRADE FOR FACTORY KEYLESS ENTRY INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an Alarm Upgrade System by Crimestopper Security Products Inc. This booklet contains the information necessar y for installing, using, and maintaining this system.
COMPONENT MOUNTING Control Unit: DO NOT mount or wiring harness where they can become entangled with moving parts such as brake/gas/clutch pedals, or th e steering column! The control module should be mounted in a concealed location. Do not mount the control unit in the engine compartment.
WIRING ORANGE WIRE: ( - ) NEGATIVE STARTER DISABLE (Armed output) Ground output when system is armed. This output is used for disabling the starter or to activate other option al devices such as scanner LED’s, window control modules, voice modules etc.
WIRING GREEN WIRE: ( - ) HOOD/TRUNK TRIGGER Connect this wire to a grounding hood / trunk pin switch or to existing factory hood and trunk pin switches that read ground when open. If no existing switches are available, new pin switches may be installed.
4 ON CURRENT SENSING DIP SWITCH #4 OFF CURRENT SENSING The CS - 882OEM system includes a current sensing circuit to monitor current flow through the vehicles electrical system.
2 3 1 4 ON NEGATIVE VALIDATION INPUTS (TOP EDGE OF 882 MODULE) 2 3 1 4 ON POSITIVE VALIDATION INPUTS (TOP EDGE OF 882 MODULE) DOOR / LOCK & VALIDATION WIRES (TYPICAL INSTALLATION) VALIDATION WIRES.
PROGRAMMABLE OPTIONS 1. Turn the Ignition ON and press the Override/Program button 7 times within 10 seconds. 2. Turn OFF Ignition. LED will flash slowly once per second as and indicator the system is in programming mode. 3. Within 20 seconds, press the Override/Program button the number of times that corresponds to the feature list below.
OPERATION ARMING To arm the alarm and lock the doors, press the Lo ck button of your Factory Keyless Remote Control. The 882 OEM system will sense the Door Lock signal and Arm. The lights will flash once, the vehicle horn or siren will chirp once. After 3 seconds, the LED indicator will begin flashing slowly and Immobi lizer circuits become active.
OPERATION VALET MODE To disable alarm fun ctions of the 882 system, turn the Ignition ON and press the override/program button 3 times within 8 seconds. After 8 seconds, the dash LED turns on solid as an indicator that the system is in valet mode. Repeat this steps to exit VALET mode.
WIRING DIAGRAM VALET/ IGN SW. STARTER STATUS LED FUSE BOX IGNITION ON & CRANKING VOLTAGE STARTER WIRE 85 87A CUT 86 30 RED VIOLET BLACK WHITE/RED (-) ARMED OUTPUT (STARTER DISABLE) IGN SW.
An important point after buying a device Crimestopper Security Products CS-882 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Crimestopper Security Products CS-882 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Crimestopper Security Products CS-882 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Crimestopper Security Products CS-882 you will learn all the available features of the product, as well as information on its operation. The information that you get Crimestopper Security Products CS-882 will certainly help you make a decision on the purchase.
If you already are a holder of Crimestopper Security Products CS-882, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Crimestopper Security Products CS-882.
However, one of the most important roles played by the user manual is to help in solving problems with Crimestopper Security Products CS-882. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Crimestopper Security Products CS-882 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
