Instruction/ maintenance manual of the product CS-2004TW1 Crimestopper Security Products
Go to page of 20
CS-2004TW1 with 2-Way Paging Remote & 1-Way ‘Sidekick’ Remote CS-2004DC with two 1-Way Remotes INSTALLATION & OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a Security System by Cr imestopper Security Products Inc.
TABLE OF CONTENTS Installation Cautions & Warnings…….………………………………………………………………...………………2 Suggested Component Mounting………….……………………………………………………………….
CONTROL MODULE / COMPONENT MOUNTING DO NOT Mount the control unit or wiring harness in th e engine compartment or anywhere they can become entangled with moving parts such as brake/g as/clutch pedals, or the steering column. The alarm control module should be mounted in a concealed location.
WIRING BLUE WIRE: (-) HOOD/TRUNK TRIGGER The Blue wire is used for a grounding hood pin switch, trunk pin or both. Connect to existing hood and trunk pin switches that read ground when open. If no existing switches are available, install new pin switches if desired.
WIRING WHITE/RED WIRE: (-) REMOTE OUTPUT #2 (Optional, Requires Relay) This wire provides a momentary (-) Negative auxiliary Ou tput when Button #4 is pressed and held for at least 2 seconds. Connect this wire to terminal 85 of a relay to operate an AUX device or function.
POWER DOOR LOCK WIRING 6-PIN DOOR LOCK PLUG 18 GA. (Optional / ON-Board Relays): VIOLET: DOOR LOCK Relay Term. #87: Normally Open [Polarity Input for Lock relay] WHITE: DOOR LOCK Relay Term. #30: Common [Lock Output] GRAY: DOOR LOCK Relay Term. #87A: Normally Closed VIO/WHT: DOOR UNLOCK Relay Term.
POWER DOOR LOCK DIAGRAMS UL REVERSE P OLA RITY DOOR LOCK WIRING + L NEGA TIVE TRIGG ER D OORLOCK WIRING UL L NOT USED UNLO CK W I RE CUT LOCK W I RE CUT FAC T O RY LOCKING RELA YS UL L + A F TERMA RKE.
STARTER DISABLE WIRING STARTER DISABLE PLUG: 3 ORANGE 14 GA. WIRES: (PROGRAMMABLE: Normally Closed or Normally Open Configuration with ON-Board Relay ) Note: READ BELOW before connecting starter disable! Norm ally OPEN must be programmed to operate. See pg 10.
SYSTEM WIRING DIAGRAM 87 30 87 30 87 30 IGNITION ST AR TER SWITCH 85 86 85 86 85 86 PA R K I N G LIGHTS (-)REMOTE OUTPUT 2 (-)REMOTE OUTPUT 1 BA TTER Y - BLA CK/ WHITE (-)DOME LIGHT WHITE/R ED GRA Y C.
CS-2004TW1 ANTENNA The following diagram pertains to the CS-2004TW1 model only: WINDSHIELD ANTENNA LOCA TIONS CS-2004TW1 Black P lug Blue Plug RECOMMENDED Note Orientation of Black & Blue Pl ugs.
OPTION PROGRAMMING To Engage Option Programming: 1. Turn Key to the ON position and wait 5 seconds. 2. Press program / valet button 5 times, after a few sec onds the unit will flash the lights 5 times and the LED will light solid. 3. Push the valet/program button [again] the number of times that corresponds to the option number desired (1 thru 13).
OPTION PROGRAMMING 2. PASSIVE ARMING This option controls the Passive (Automatic) arming feature. If ON, arming will occur 30 Seconds after the ignition is turned off and the last door has been closed. The LED w ill begin flashing rapidly. If a door is reopened, the system will wait (LED solid) for the door or zone to close before arming.
OPTION PROGRAMMING 11. DOUBLE UNLOCK PULSE This option controls whether the unit will send one or tw o unlock pulses when disarmed. This feature may be required for interfacing to existing Factory Keyless Entry or Alarm systems in a vehicle. These systems are found on some Nissan, VW, Toyota, and Lexus vehicles.
CS-2004TW1 / CS-2004DC TRANSMITTER PROGRAMMING SEE NOTES LAST PAGE! 1. Turn key to the ON position and wait 5 seconds. 2. Press Programming/Valet button 4 times. 3. After a few seconds, the unit will flash the parking lights 4 times. 4. A. FOR CS-2004TW1: Press Buttons #1 & 2 together on the remote you wish to program.
OPERATION SLNT AUX ARM/ DISARM/ UNLOCK LOCK PA G I N G LED's SILENT/ AUX. 2 ANTENNA FIXED AUX. 1 #1 #2 #3 #4 CS-2004T W1 LE D P AGING R EMOTE CS-2004DC / CS-2004TW1 remote controls: #3 #1 CS-2004TW 1 ONE-W A Y REMOT E #2 #4 SLNT AR M / AU X . # 1 SIL ENT / AU X .
OPERATION ACTIVE ARMING To arm the alarm and lock the doors, press the #1 Button on any remote. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock (optional) and the starter will be disabled. The red in- dash LED in the vehicle will begin to flash.
OPERATION SHOCK / IMPACT PROTECTION WITH PRE-WARNING Once the system is armed, if a low-level shock to the v ehicle body is detected, the pre-warning sensor activates with 5 siren chirps and one light flash as a Warn-Away feature. If a hard impact to the vehicle is detected the system will go into a full trigger cycle for 20 seconds.
OPERATION PASSIVE ARMING / PASSIVE LOCK MODES If programmed, passive (Automatic) Arming will occur 30 Se conds after the ignition is turned off and the last door has been closed. The lights will flash twice when the last door is closed and the LED will begin flashing rapidly while counting down.
OPERATION LED TRANSCEIVER (LOW BATTERY WARN) CR2032 3V Lithium Battery T wist and Remove Battery cover with a Coin or Screwdriver Larger "+" Positive side of ba ttery faces up CS2004TW 1 BA TTER Y REPLACEMENT The CS-2004TW1 LED has a lo w battery warning system.
CARJACK PROTECTION PROGRAMMABLE PASSIVE CARJACK This feature provides Passive Carjack protecti on and must be enabled before use through Alarm programming options #7 & #12 on page 10. We recommend this mode should only be used in serious situations.
An important point after buying a device Crimestopper Security Products CS-2004TW1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Crimestopper Security Products CS-2004TW1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Crimestopper Security Products CS-2004TW1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Crimestopper Security Products CS-2004TW1 you will learn all the available features of the product, as well as information on its operation. The information that you get Crimestopper Security Products CS-2004TW1 will certainly help you make a decision on the purchase.
If you already are a holder of Crimestopper Security Products CS-2004TW1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Crimestopper Security Products CS-2004TW1.
However, one of the most important roles played by the user manual is to help in solving problems with Crimestopper Security Products CS-2004TW1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Crimestopper Security Products CS-2004TW1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
