Instruction/ maintenance manual of the product CS-9704 CrimeStopper
Go to page of 12
CS-9704RS INTEGRATED ALARM/REMOTE START SYSTEM INSTALLATION / OPERATING MANUAL INTRODUCTION: This is a combination vehicle security alarm and tach-l ess remote start system for 12-volt motor vehicles. There are a variety of built-in features, which you may or may not use.
INSTALLATION CAUTIONS & WARNINGS 1. BEFORE BEGINNING , check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, AND BATTERY). 2. TO PREVENT A POSSIBLE DEAD BATTERY remove vehicle dome light fuse while working on the vehicle.
WIRING J-1 6 PIN HI-CURRENT CONNECTORS (See Wire diagram at back of manual for Details) RED : +12V INPUT RED : +12V INPUT (30 Amp) BROWN: IGNITION 1 (Secondary Ign.
WIRING GRAY WIRE: PIN 6: Engine Monitor (used for tach mode only) Used to monitor when the engine is running. Connect to negat ive terminal of ignition coil, crankshaft position sensor or ECM/PCM tach wire. An alternate method is to wrap several turns around a spark plug wire and fasten with wire ties or hi-temp plastic clamps.
WIRING J-3 2 PIN PLUG (WHITE) RED-BLACK WIRE: PIN 1: DOME LIGHT ILLUMINATION (-) ( REQUIRES RELAY ) Connect to terminal 85 of relay. This wire turns the dom e light on for 30 seconds upon disarming of the alarm. If the ignition is turned on or the alarm is re-armed, the dome light will turn off again.
This system performs the following tasks by pressing one of the buttons on the hand-held transmitter: • ARM / LOCK • DISARM / UNLOCK • TRUNK POP • REMOTE START • PANIC Note: You may not have all of the available features depending on your particular installation.
REMOTE ENGINE START: Press and hold the Remote Start button on the transmitter until you hear 3 siren chirps (release button) then the parking lights will turn on. The vehicle will start and run for 15 minutes unless you press the Remote Start transmitter button again or press the foot brake in the vehicle.
ACTIVE RE-ARMING: Active Re-arming means that the system will re-arm itself 30 seconds after disarmed with the transmitter if a door has not been opened. This is handy if the vehicle is acci dentally disarmed without you knowing it. This feature can also be turned off with the programming options.
9 To eliminate siren chirps, turn the ignition on and press t he transmitter’s remote start button for about 3 seconds. You will hear a short double chirp. After the ignition is turned off, there will be no siren chirps for arm, disarm and remote start engage/reset confirmation.
This feature controls the length of time the starter stays engaged. If the default (0.8 seconds) is not long enough to start the engine, change the setting to1.25 seconds. GAS / DIESEL: Set this switch to select the proper vehicle fuel type. Selecting Diesel delays starter activation about 10 seconds to allow warming of glow plugs.
UNIT SHUTS DOWN 4-5 SECONDS AFTER REMOTE STARTING: The unit does not sense the engine in Tachless mode. Turn dip switch #4 OFF and wrap the gray wire around a plug/coil wire. The module will sense inducted RF/Engine noise in the gray wire allow the engine to stay running longer than 4-5 seconds.
IGNITION 1 IGNITION 1 ACC / I GN 2 BA TTERY ST ARTER +BRA KE SWIT CH (-) HOOD /TRUNK SWITCH (+) DOOR SWITCH YELLOW IGNITION SWITCH VIOLET GREEN BLUE 30A MP 20A MP 10A MP FUSE FUSE FUSE 1 2 GRA Y 0 3 4.
An important point after buying a device CrimeStopper CS-9704 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CrimeStopper CS-9704 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CrimeStopper CS-9704 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CrimeStopper CS-9704 you will learn all the available features of the product, as well as information on its operation. The information that you get CrimeStopper CS-9704 will certainly help you make a decision on the purchase.
If you already are a holder of CrimeStopper CS-9704, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CrimeStopper CS-9704.
However, one of the most important roles played by the user manual is to help in solving problems with CrimeStopper CS-9704. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CrimeStopper CS-9704 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
