Instruction/ maintenance manual of the product Power Switching Crestron electronic
Go to page of 16
CRESTRON GREEN LIGHT™ Power Switching Introduction CRESTRON GR EEN LIGHT power switc hing cabinets c ome pre-c onfigured wi th GLXP m odules already installed.
Power Switching CRESTRON GREEN LIGHT™ Physical Description This section shows the ex terior and interior di mensions of t he CRESTRO N GREEN LIGHT cabinet.
CRESTRON GREEN LIGHT™ Power Switching Interior Dimensions of CRESTR ON GREEN LIGHT Cabinets (120/208 VAC, left; 277/480 VA C, right) H1 H1 1 7 8 " (48 mm) 8 1 8 " (2 07 mm) 1 7 8 " (4.
Power Switching CRESTRON GREEN LIGHT™ Installation Observe the following when installing the cabinet: • The cabinet m ust be mounte d by a licensed electrician in accorda nce with all nati onal and local codes. Refer to the diagram below for specific requirem ents.
CRESTRON GREEN LIGHT™ Power Switching Wiring NOTE: All wiri ng must be i nstalled in acc ordance with all local and nati onal electrical codes. NOTE: Refer to t he torque set tings specified o n pages 6, 7 and 8. CRESTRON GREEN LIGHT cabinets are shippe d with GLXP mo dules installed and prewired to the branch circuit breakers.
Power Switching CRESTRON GREEN LIGHT™ Feed Wiring (Section A) Feed Wiring for MLO (left) and MCB (right) Applicat ions Refer to the foll owing table for inform a tion on wiring the feed to the panel.
CRESTRON GREEN LIGHT™ Power Switching Load Wiring (Section B) CAUTION: Bypass jum pers are provided on each output to allow testing an d to protec t the module duri ng installation. The jumper shorts the L and SW terminals so that th e load circu it is energized when the branch breake r is on.
Power Switching CRESTRON GREEN LIGHT™ The GLXP-DIMFLV 8 also requi res wirin g the term inals for 0-10 VDC cont rol wire. Refer to the following diagram when connecting the dimmable ballast. Each control wire terminal accepts one 12 – 28 AWG wire.
CRESTRON GREEN LIGHT™ Power Switching Connector Wiring RED WHITE BLUE BLACK NET: TO CONTROL SYSTEM AND OTHER CRESNE T DEVICES POWER: 24 VDC JUMPERED FRO M NET PORT or EX TERNAL S UPPLY.
Power Switching CRESTRON GREEN LIGHT™ To power the modules ext ernally from a Cresnet 24 VDC power suppl y, connect the external p ower sup ply to the EXT and G pins on the POWER suppl ied connector as shown in t he followi ng diagram .
CRESTRON GREEN LIGHT™ Power Switching Testing Manual Control A lighting module can be manuall y controlle d from its front pa nel. GLXP-SW and GLXP-HSW Modules: The state of ea ch output ca n be manual ly controlle d from t he front panel. To toggle the outpu t between off and on , tap the appropriate ON/OFF button.
Power Switching CRESTRON GREEN LIGHT™ System Operation and Commissioning This cabinet has been desig ned as a com ponent of a pro grammed C restron system. Sy stem comm issioning by an authorized Crestr on representative must be performed to ensu re system operatio n.
CRESTRON GREEN LIGHT™ Power Switching Problem Solving Troubleshooting The following table prov ides corrective action for po ssible trouble situations. If further assistance is required, please contact a Crestron custom er service representative. Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTIO N Power not delivered to the module.
Power Switching CRESTRON GREEN LIGHT™ Appendix A: Setting Module Net IDs The following procedure will normally be performed by an au thor ized Crestron representative as part of the System Commissioni n g pha se. For system wiri ng and basic te sti n g as desc ri be d on pages 5 and 11, it is not nec essary to perform this step.
CRESTRON GREEN LIGHT™ Power Switching Appendix B: Module Specifications Specifications for the GLXP modules are li sted in the following tabl e. GLXP Module Specification s SPECIFICATION GLXP-SW10 G.
Power Switching CRESTRON GREEN LIGHT™ Return and Warranty Policies Merchandise Returns / Repair Service 1. No mer ch and ise may be r etu rne d for credit, exchange or service without prior authorizatio n from CRESTRON. To obtain w arranty service for CRESTRON pro ducts, conta ct an authori zed CRESTRON dealer.
An important point after buying a device Crestron electronic Power Switching (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Crestron electronic Power Switching yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Crestron electronic Power Switching - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Crestron electronic Power Switching you will learn all the available features of the product, as well as information on its operation. The information that you get Crestron electronic Power Switching will certainly help you make a decision on the purchase.
If you already are a holder of Crestron electronic Power Switching, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Crestron electronic Power Switching.
However, one of the most important roles played by the user manual is to help in solving problems with Crestron electronic Power Switching. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Crestron electronic Power Switching along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
