Instruction/ maintenance manual of the product W120FW Creda
Go to page of 16
W ashing Machine W100FW / W120FW / W120VW Retention of this Instruction Book Keep this book in a handy place for reference . It contains important details on the safe and proper use of your appliance .
P ositioning & Adjusting the feet Choosing the position of your appliance will influence its per formance. ★ Position where possible on a solid floor . Some vibration may occ ur with a wooden floor . ★ T ake care with vinyl floor coverings. The weight of the appliance may cause indentations in some vinyl floor coverings.
Hot and Cold Fill Connection 1. Connect the straight end of the supplied RED or GREY hose to the HOT water supply tap (Fig 1). Connect the straight end of the supplied BL UE hose to the COLD water supply tap . 2. Hand tighten connectors sufficiently to ensure wat er does not leak from the hose connections.
4 C onnec t to a dr ainage sy stem ● Do not remove hooked end support from drainage hose . ● Do not position standpipe near an electrical outlet. F or drainage into a standard work top sink ensure outlet pipe h as a minimum bore of 32 mm. T o avoid syphoning ensure the end of the drainage hose is abov e the water level in the sink.
14 W ashc ar e Tips ★ W e strongly recommend that your do not wash under wired bras in this machine. Should the wires become detached they could cause damage to your clothes and the machine . If the washcare label states that the garment is machine washable then we advise placing it in a sealed pillow case or similar washbag.
1. Sor t laundry into same wash requirements. 4. Select wash programme by turning the wash dial clockwise. 5. Select optional wash fea tures by pressing required button. 2. Close door , applying pressure only at the 2 o ’clock position. 7. Check water and electricity are switched on at mains.
W ash dial and symbols V ariable spin speed con trol dial (Model W120VW only) Before selecting a programme, ensure the mains button is in the ‘OFF’ position. T urn the dial slowly clockwise. Y ou will hear as the pointer aligns with the star t of the selected wash programme, final rinse or spin.
Choosing a wash programme 8 IT CL Prog. C o des T emp ˚C 40 3kg to 5.5kg 15 - 25 400 F ull Load Appro x Prog .Time (mins) based on hot and cold fill Maximum Spin Sp eed (rpm) depending on Model F abric A Prew ash Heavily soiled loads. On completion, switch ‘OFF’ mains button before selecting wash programme.
9 BUT T ON SELECTION T o selec t, press the button and the button comes out. T o cancel, press again and the button is flush with the console. Remember to cancel buttons af ter use! ENERGY SA VE Save money and time on lightly soiled loads. Lightly soiled loads are washed at the temperatur e of the incoming household water supply .
CHOOSE A SUIT ABLE DETERGENT ★ Select ‘ low suds’ automatic washing powder , designed specifically for automatic washing machines or washer dryers. ★ F ollow manufacturer ’ s dosage recommendations . Do not under dose, you will not achieve a clean wash.
T o obtain claimed energy label wash per formance for a 60° C cotton wash, dispense pow der detergent in a dosing ball, plac ed in an upright position in the centre of the wash load (F ig 5).
W ARNING ● Do not clean any part of your appliance with abrasive cleaners, sc ouring agents, acids, chlorine based bleach or metal polish as they may cause damage.
© REPRODUCED BY KIND PERMISSION OF LEVER BROS. LIMITED Regular Checks and Stain Remov al Regular checks As with any major appliance, there are certain aspec ts which require regular attention. Listed below are a number of such key areas which you should check regularly .
14 Before calling y our nearest Service Office, look at this list, to find a possible solution to your problem. My appliance will not fill or take in detergent... ★ Is the machine plugged in and switched on? ★ Is the socket OK? T r y another appliance in the socket.
The cost of par ts where required will be charged additional to the fixed labour charge, but again this cost will have a maximum level of which you will be advised by your Regional Ser vice Centre . The repair itself is fully guaranteed for 12 months.
F or more information on our exciting product range ring Creda Answ er C entre 08701 54 64 74 016437794-02 Printed by SIMLEX • FOUR ASHES, WOL VERHAMPTON K ey C ontac ts Ser vice UK: 08709 066 066 R.
An important point after buying a device Creda W120FW (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Creda W120FW yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Creda W120FW - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Creda W120FW you will learn all the available features of the product, as well as information on its operation. The information that you get Creda W120FW will certainly help you make a decision on the purchase.
If you already are a holder of Creda W120FW, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Creda W120FW.
However, one of the most important roles played by the user manual is to help in solving problems with Creda W120FW. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Creda W120FW along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
