Instruction/ maintenance manual of the product 917.28746 Craftsman
Go to page of 18
@SearsBrands, l.l..C For answers to your questions about this product, Call: 1-800-659-5917 Sears Craftsman Help Line 5 am - 5 pm,Mon - Sat This product has a low emission engine which operates differently from previously built engines. Before you start the engine, read and understand this Owner's Manual.
TABLE OF CONTENTS SAFETY RULES WARRANTY LIMITED WARRANTY ON CRAFTSMAN TRACTOR AND BATTERY 2-YEAR ON TRACTOR When used and maintained according to the operator's manual instructions; if this tractor fails due to a defect in material or workmanship within two years from the date of pur- chase, call 1-800-4-MY-HOME@ to arrange for free repair.
SAFETY RULES SAFETY RULES • Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel . spillage and remove any fuel-soaked debris. Allow machine to cool before storing. • If you strike a foreign object, stop and inspect the machine.
(1) 1-1/40.0. Washer @ (1) Locknut 3/8-16 Slope Sheet ~ (2) Rear Lift Link Assemblies Mower Install Sheet Mower Front Wheel Mower (2) Keys @ (1) 3/4 0.0. Washers ~ (2) Small Retainer Springs - 5/16 UNASSEMBLED PARTS (1) Whee! (i) ~i"'---'.
- Pivot bar towards you and insert oth- er end of bar into hole in rear mower bracket (D). Move mower as needed to insert bar. - Secure with washer and retainer spring as shown. A '-" NOTE: Be sure mower side suspension arms (A) are pointing forward before slid- ing mower under tractor.
II .ICHECKLIST Before you operate your new tractor, we wish to assure that you receive the best performance and satisfaction from this Quality Product. Please review the following checklist: ~ All assembly instructions have been completed. ~ No remaining loose parts in carton.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.
TO ADJUST MOWER CUTTING HEIGHT The position of the attachment lift lever (A) determines the cutting height. • Put attachment lift lever in desired cut- ting height slot. • Slide pointer tab (T) to desired cutting height as a reminder for next time you mow.
the attachment engaged. Do not mow in reverse unless absolutely necessary. USING THE REVERSE OPERATION SYSTEM - Only use if you are certain no children or other bystanders will enter the mowing area. 1. Depress brake pedal all the way down. 2. With engine running, turn ignition key counterclockwise to"ROS "ON" posi- tion.
4. Move throttle control to fast position 5. Pull choke control out for a cold engine .start attempt. For a warm engine start attempt the choke control may not be needed.
MAINTENANCE ROS "ON" Position • When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should NOT shut off the engine. BLADE CARE For best results mower blades must be sharp.
Oil Drain Valve Change the oil after every 50 hours of op- eration or at least once a year if the tractor is not used for 50 hours in one year. Check the crankcase oil level before start- ing the engine and after each eight (8) hours of operation. TO CHANGE ENGINE OIL Determine temperature range expected before oil change.
A CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth. 2. Raise mower to its highest position. 3. At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground.
Loosen jam nut A first NOTE: Each full turn of the adjustment nut will change mower height about 1/8". • Recheck measurements, adjust if nec- essary until front tip of blade is 1/8" to 1/2" lower than the rear tip. • Hold adjustment nut in position with wrench and tighten jam nut securely .
TO CHECK BRAKE If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. You may also check brake by: 1. Park tractor on alevel, dry concrete or paved surface, depress clutch/brake pedal all the way down and engage parking brake.
STORAGE Immediately prepare your tractor for stor- age at the end of the season or if the trac- t~.r will not be used for 30 days or more. aWARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Loss of poWer 6. Faulty spark plug. 6. Clean and regap or change (continued) spark plug. 7. Dirty fuel filter. 7. Replace fuel filter.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION - - - A WARNING: To avoid serious Injury, operate your tractor up and down the face of slopes, never across the face. Po not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control.
An important point after buying a device Craftsman 917.28746 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Craftsman 917.28746 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Craftsman 917.28746 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Craftsman 917.28746 you will learn all the available features of the product, as well as information on its operation. The information that you get Craftsman 917.28746 will certainly help you make a decision on the purchase.
If you already are a holder of Craftsman 917.28746, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Craftsman 917.28746.
However, one of the most important roles played by the user manual is to help in solving problems with Craftsman 917.28746. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Craftsman 917.28746 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
