Instruction/ maintenance manual of the product 79689 Craftsman
Go to page of 20
OWNERS MANUAL MODEL NO. 247.796890 _ WARNING Carefully read and follow Safety Rules, Precautions and Operating Instructions, Failure to do so can result in serious personal injury.
REAR Eel Ramp Muffler Cleaner Control Tank lopper Chip-It Chute Deflector Spark Plug. and Elbow Catcher Starter Bag Model Plate FRONT INDEX MODEL NUMBER SERIAL NUMBER THE MODEL AND SERIAL NUMBERS WILL.
WARNING To reduce the potential for any injury, comply with the following safety instruc- - - _ tions Failure to comply with the instructions may result in personal injury RULES FOR SAFE OPERATION TRA.
NOTE This unit is shipped WITHOUT GASOLINE or OIL, After assembly, see operation section of this manual for proper fuel and engine oll recommendations ASSEMBLY INSTRUCTIONS Tools Required for Assembly.
No Self-Tapping Screws (C) Lower Leaf Ramp Section INSTALLATION OF HOPPER AND UPPER GUItDE EXTENSION 1. The lower leaf ramp section on the chipper-shred- der is placed in an upright position for shipping purposes Lower this section, 2, Place the hopper in position on the shredder -- m See figure 3.
ATTACHING THE CATCHER BAG Your unit is equipped with a nylon bag which attaches to the discharge opening. If desired, place the end of the bag over the chute deflector. Depress plunger, pull on the drawstring, and reIease plunger to lock it in position.
FIGURE 9. TO START ENGINE 1, Attach spark ptug wire and boot to spark plug 2. Place the throttle control lever in START position See figure 8 3. Grasp starter handfe (see figure 9) and pull rope out slowly until engine reaches start of compres- sion cycle (rope will pull slightly harder at this point).
Lower the leaf ramp by holding the handle and pulling up on the release bar See figure 12 Leaves and small twigs can be raked into the chipper-shredder with the leaf ramp in this position See figure 13 Handle Leaf Ramp No larger than 1t2 inch diameter FIGURE 14.
ADJUSTMENTS CARBURETOR ADJUSTMENT If any adjustments are made to the engine while the engine if running {eg. car- buretor), keep clear of all moving parts Be careful of heated surfaces and muffler Min.
AIR CLEANER The air cleaner prevents damaging dirt, dust, etc, from entering the carburetor and being forced into the engine and is important to engine life and performance Never run your engine witho.
LUBRICATION Wheels - The wheels require no lubrication, Flails and Fingers - If the unit is disassembled for any reason, lubricate the flails and fingers with a light oil (engine oil may be usedt CUTT.
MAINTENANCE CHECK LIST SERVICE RECORD FILL tN DATES AS YOU COMPLETE REGULAR SERVICE Check Engine Oil Level Change Engine Oil SERVICE DATES Clean Engine Service Air Cleaner , , .
Repair Parts 5 H.P. Chipper-Shredder--Model 247.796890 3 4 5 1 2 9 42 13 14 /7 5? 18 / 38 34 24 25 20 43 53 52 13.
Repair Parts 5,H°P. Chipper-Shredder--Model 247_796890 Key Non Part Noo Description 1 2 3 4 5 6 7 8 9 11476 710-0465 711-0580 711-0579 11455 736-0921 726-0111 712-0922 714-0507 10 16568 11 712-0107 1.
Repair Parts 5 H.P, ChipperShredder--Model 247.796890 Engine--Model 130212 Type 1731-01 26 541 ( ) P 30 615 @6' 230 383 741 16 219 46 @ 220 _'25 36 208 201 35 529 _IIC SPE¢IALIOOLS REQUIRED.
Repair Parts 5' H.R Chipper-Shredder--Mode! 247.796890 Engine--Model 130212 Type 1731-01 *BEouInEs SPECIAL TOOLS Zo_ LNS_T .ALL SEE REPAIR INSTRUCTION MANUAL.
Repair Parts 5 H,P. Chipper-ShredderiModel 247,796890 Engine--Model 130212 Type 1731-01 124 634_e_e,,_ 152 609 u_ _ _(_ 542 03 205 612 ]4u _ _ J ' lfi_b1394 433 191 190 2O6 409 473 621 223 526 2.
Repair KEY NO 1 2 3 5 7 8 9 10 tl 12 13 14 T5 16 18 19 20 21 22 23 24 25 PISTON 26 27 28 29 30 Parts 5' H.P_ Chipper-Shredder-- Model 247,796890 Engine-Model 130212 Type 1731-01 PAR3" NO.
Repair Parts 5 H°P. Chipper-Shredder--Model 247.796890 Engine--Model 130212 Type 1731-01 KEY NO. 191 200 201 202 203 204 205 206 208 209 l 216 217 2191 220 223 224 227_ 230i 256 298 299 304 305 306 307 308 333 335 337 346 356 358 363 373 383 392 394 409 432 433 434 PART NO.
,£'_._/_/,e,@ OWNERS MANUAL MODEL NO. 247.796890 HOW TO ORDER REPAIR PARTS @_/_/,_,@ / C R R F T.S M A N® 5 H.P. CHIPPER-SHREDDER The model number will be found on the model plate, attached to .
An important point after buying a device Craftsman 79689 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Craftsman 79689 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Craftsman 79689 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Craftsman 79689 you will learn all the available features of the product, as well as information on its operation. The information that you get Craftsman 79689 will certainly help you make a decision on the purchase.
If you already are a holder of Craftsman 79689, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Craftsman 79689.
However, one of the most important roles played by the user manual is to help in solving problems with Craftsman 79689. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Craftsman 79689 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
