Instruction/ maintenance manual of the product 390.262653 Craftsman
Go to page of 12
SEARS OWNER'S MANUAL MODEL NO. 390.262454 390.262553 390.262653 CAUTION: Read and Follow All Safely Rules and Operating Instructions Before First Use of This Product. Save This Manual For Future Reference. MODEL NOS. 390.262454 390.262553 MODEL NO.
CONTENTS INTRODUCTION/XVARRANTY .......................................... 2 SAFETY ............................................................................... 2 PREPARATION .................................................................... 3 INSTALLATION .
PREPARATION BASIC TOOLS AND MATERIALS NEEDED Pipe Wrenches Screwdriver Hacksaw Check Valve Adjustable Wrench Teflon Tape Knife INSTALLATION (Continued) Suction Pipe iTee and Plug NOTICE: Depth to water must not be more than 20'. 1. Long runs and many fittings increase friction and reduce flow.
INSTALLATION (Continued) 2. To aid priming on driven point installations, install a line check valve as shown in Figure 2. Be sure check valve flow arrow points toward pump. DISCHARGE PIPE SIZES 1. If increasing discharge pipe size, install reducer in pump discharge tapping.
ELECTRICAL Connection diagram for dual voltage, single-phase motors. Your dual-voltage motor's terminal board (under the motor end cover) will match one of the diagrams below. Follow that diagram if necessary to convert motor to 115 Volt power. Connect power supply wires to L1 and L2.
ELECTRICAL (Continued) 3. Disconnect power before servicing motor or pump. If the disconnect switch is out of sight of pump, lock it open and tag it to prevent unexpected power application. 4. Ground the pump permanently using a wire of the same size as that specified in wiring chart (below).
OPERATION PRIMING THE PUMP NOTICE: 'Priming' refers to the pump expelling all air in the system and beginning to move water from its source out into the system. It does not refer only to pouring water into the pump (although pouring water in is usually the first step).
MAINTENANCE Pump and piping need not be disconnected to repair or re- place motor or seal (see Figure 12). If motor is replaced, re- place the shaft seal (Key No. 6, Page 11). Keep one on hand for future use. Be sure to prime pump before starting. NOTICE: Check motor label for lubrication instructions.
MAINTENANCE (Continued) 4. Place pump body half face down on flat surface and tap out stationary half of seal (see Figure 16). 9. Hold motor shaft with 7/16" open end wrench on shaft flats (Figure 14, Page 8) and screw impeller onto shaft. Be sure you do not touch capacitor terminals with body or any metal object.
TROUBLESHOOTING CHART SYMPTOM CORRECTIVE ACTION Motor will not run f. Be sure switch is on POSSIBLE CAUSE(S) 1. Disconnect switch is off 2. Fuse is blown 3. Starting switchis defective 4. Wires at motor are loose, disconnected, or wired incorrectly 2.
REPAIR PARTS 20 3 4 8A 11A 1. Sears Product Service,1-800-366-7278 12" , ..... 3 10 y I F>mr,'_ 10 Key No 1 1A 1B IC 2 3 4 5 6 7 8 8A 9 10 11 11A 12 13 14 16 17 16 19 20 21 Motor Overload Protector Terminal Board Contactor Governor Capacitor Shnger Priming Plug 1/2' NPT 390.
S£ A[RS OWNER'S MANUAL Model No. 390.262454 390.262553 390.262653 The model number of your Sprinkler Pump will be found on a plate attached to the side of the pump body.
An important point after buying a device Craftsman 390.262653 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Craftsman 390.262653 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Craftsman 390.262653 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Craftsman 390.262653 you will learn all the available features of the product, as well as information on its operation. The information that you get Craftsman 390.262653 will certainly help you make a decision on the purchase.
If you already are a holder of Craftsman 390.262653, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Craftsman 390.262653.
However, one of the most important roles played by the user manual is to help in solving problems with Craftsman 390.262653. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Craftsman 390.262653 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
