Instruction/ maintenance manual of the product 358.79821 Craftsman
Go to page of 13
Operator's Manual CRFIFTSMFIN 24cc/1.3 cu.in. 2-Cycle 17 Inch Cutting Path / .080 In. Line GASOLINE WEEDWAOKER ® Model No. 358.798210 WARNING: Read and follow all Safety Rules and Operating Instructions before first use of this product. For answers to your questions about this product: Call 7 am-7 pm, Mon.
Warranty Statement 2 Storage 11 Safety Rules 2 Troubleshooting Chart 12 Assembly 4 Emissions Statement 12 Operation 5 Parts List 14 Maintenance 9 Spanish 17 Service & Adjustments 10 Parts and Ordering Back FULL ONE YEAR WARRANTY ON CRAFTSMAN :_ GAS POWERED WEEDWAOKER _; LINE TRIMMER.
OPERATOR SAFETY • Always wear safety eye protection. • Always wear long pants, long sleeves, boots, and gloves. Wearing safety leg guards is recommended. Do not go barefoot or wear sandals. Stay clear of spinning line. • Secure hair above shoulder length.
tor screen. If you operate in a locale where such regulations exist, you are legally responsible for installing and maintaining the operating condition of these parts. Failure todo so is a viola- tion of law. Contact a Sears Service Center for the correct parts.
KNOW YOUR TRIMMER READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the loca- tion of the various controls and adjustments. Save this manual for future refer- ence.
Never use engine or carburetor clean- er products in the fuel tank or perma- nent damage may occur. See the STORAGE section for addi- tional information. STOPPING YOUR ENGINE • Press and hold the On/Stop switch in the STOP position. • If engine does not stop, move choke lever to full position.
OPERATING INSTRUCTIONS OPERATING POSITION ALWAYS WEAR: _ _. _ j_ Eye Protection H_°;gY _t_s __ Cut from your right to your left. Bring the engine to cutting speed be- fore entering the material to be cut. Do not run the engine at a higher speed than necessary.
• For trimming or scalping use less than full throttle toincrease line life and decrease head wear especially: • During light duty cutting • Near objects around which the line can wrap such as small posts trees or fence wire • For mowing or sweeping use full throttle for a good clean job WARNING:Always wear eye protec- tion.
MAINTENANCESCHEDULE CARE & MAINTENANCE TASK WHEN TO PERFORM Check for Loose fasteners and parts Before each use Check for damaged or worn parts Before each use Clean unit and labels After each use.
REPLACING THE LINE • Push and hold the engine stop switch in the stop/off position until the unit has fully stopped. • Disconnect the spark plug lead wire. • Remove the spool by firmly pulling on the tap button. • Clean entire surface of hub and spool.
ADJUSTING PROCEDURE Idle Speed Allow engine to idle. Adjust speed until engine runs without stalling. • Turn clockwise to increase engine speed if engine stalls or dies. • Turn counterclockwise to decrease speed. No further adjustments are necessary if performance is satisfactory.
TROUBLESHOOTING CHART TROUBLE Engine will not start. Engine will not idle properly. Engine will not accelerate, lacks power, or dies under a load. Engine smokes excessively. Engine runs hot. CAUSE • Engine flooded. • Fuel tank empty. • Spark plug not firing.
under Emissions Control Warranty Parts List) is defective or a defect in the materials or workmanship of the engine causes the failure ofsuch an emission related part, the part will be repaired or replaced by SEARS.
An important point after buying a device Craftsman 358.79821 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Craftsman 358.79821 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Craftsman 358.79821 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Craftsman 358.79821 you will learn all the available features of the product, as well as information on its operation. The information that you get Craftsman 358.79821 will certainly help you make a decision on the purchase.
If you already are a holder of Craftsman 358.79821, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Craftsman 358.79821.
However, one of the most important roles played by the user manual is to help in solving problems with Craftsman 358.79821. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Craftsman 358.79821 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
