Instruction/ maintenance manual of the product 358.7951 Craftsman
Go to page of 13
Operator's Manual CRAFTSMAN ° 24cc/1.3 cu.in. 2-Cycle 17 Inch Cutting Path GASOLINE WEEDWACKER ® Model No. 358.795100 A WARNING: Read and follow all Safety Rules and Operating Instructions before first use of this product. For answers to your questions about this product: Call 7 am-7 pro, Mon.
Warranty Statement 2 Storage 10 Safety Rules 2 Troubleshooting Chart 12 Assembly 4 Emissions Statement 12 Operation 5 Parts List 14 Maintenance 8 Spanish 17 Service & Adjusl_nents 9 Parts and Ordering Back FULL ONE YEAR WARRANTY ON CRAFTSMAN ® GAS POWERED WEEDWACKER ® LINE TRIMMER.
OPERATOR SAFETY • Always wear safety eye protection. • Always wear long pants, long sleeves, boots, and gloves. Wearing safety leg guards is recommended. Do not go barefoot or wear sandals. Being fully covered helps protect you from debris and pieces of toxic plants thrown by spinning line.
these parts. Failure to do so is a viola- tion of law. Contact a Sears Service Center fur the correct parts. SPECIAL NOTICE: Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swellings.
KNOW YOUR TRIMMER READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the loca- tion of the various controls and adjustments. Save this manual fur future refer- ence.
and carburetor are empty. Use fresh fuel next season. Never use engine or carburetor clean- er products in the fuel tank or perma- nent damage may occur. See the STORAGE section for addition- al information. STOPPING YOUR ENGINE • Press and hold the ON/STOP switch in the STOP position.
OPERATING INSTRUCTIONS OPERATING POSITION TRIMMER HEAD Bring the engine to cutting speed be- fore entering the material to be cut. Do not run the engine at a higher speed than necessary. The cuing line will cut e_ciently when the engine is run at less than full throttle.
Scalping ......... MOWING - Your trimmer is ideal fur mowing in places conventional lawn mowers cannot reach, In the mowing position, keep the line parallel to the ground, Avoid pressing the head into the ground as this can scalp the ground and damage the tool, Mowing _.
• Clean the cover and the area around it to keep dirt from falling into the carburetor chamber when the cover is removed. • Remove parts as illustrated. • Wash the filter in soap and water. • Allow filter to dry. • Add a few drops of oil to the filter; squeeze the filter to distribute oil.
There are two adjustment screws on the carburetor. Screw (with Urniter Air Filter Cap) CARBURETOR PRESETS When making carburetor preset adjust- ments, do not force plastic limiter caps beyond stops or damage will occur. If carburetor presets are not needed, proceed to ADJUSTING PROCEDURE, IDLE SPEED.
fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Follow the mix instructions found on stabilizer container. Run engine at least 5 min- utes after adding stabilizer. Craftsman 40:1,2-cycle engine oil (air cooled) is already blended with fuel stabilizer.
YOUR WARRANTY RIGHTS AND OBLIGATIONS: The U. S. Environ- mental Protection Agency and SEARS, ROEBUCK AND CO., USA are pleased to explain the emissions control system warranty on your lawn and garden equipment engine.
WHERE TO GET WARRANTY SER- VICE: Warranty services or repairs shall be provided at all SEARS service cen- ters. call: 1-800-473-7247. MAINTE- NANCE, REPLACEMENT AND RE- PAIR OF EMISSION RELATED PARTS:.
An important point after buying a device Craftsman 358.7951 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Craftsman 358.7951 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Craftsman 358.7951 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Craftsman 358.7951 you will learn all the available features of the product, as well as information on its operation. The information that you get Craftsman 358.7951 will certainly help you make a decision on the purchase.
If you already are a holder of Craftsman 358.7951, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Craftsman 358.7951.
However, one of the most important roles played by the user manual is to help in solving problems with Craftsman 358.7951. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Craftsman 358.7951 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
