Instruction/ maintenance manual of the product 247.797852 Craftsman
Go to page of 24
I MODELNOS. 247.797852 247.797853 Caution: Readand Follow All SafetyRules and instructions Before Operating This Equipment 5 HORSEPOWER 3 CUTTUNG STAGE MULCHUNG AND BAGGING CHBPPER-SHREDDER Assembly Operation Maintenance Service and Adjustment Repair Parts SEARS, ROEBUCK ANDCO.
SAFETY RULES WARNING: TO REDUCE THE POTENTIAL FOR ANY INJURY, COMPLY WITH THE FOLLOWING SAFETY INSTRUCTIONS. FAILURE TO COMPLY WITH THE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
CONGRATULATIONS on your purchase of a Sears Craftsman Chipper-Shredder It has been designed, engi- neered and manufactured to give you the best possible dependability and performance Should you experience any problem you cannot easily rem- edy, please contact your nearest Sears Service Center/ Department.
TABLE OF CONTENTS SAFETY RULES .............................................................. 2 PRODUCT SPECIFICATIONS ............................................ 3 CUSTOMER RESPONSIBILITIES .................................. 3 WARRANTY .............
m r._i7 _=: FIGURE 1. ASSEMBLY INSTRUCTnONS Flat ---_/t_ Washer [ _ ) ] 5/16" I.D. HeX Lock ut 5/16-18 Thread Hex Bolt • ,,----5/16-18 x 8-3/8" Long IMPORTANT: This unit is shipped WITHOUT GASO- LINE or OIL After assembly, see operation section of this manual for proper fuel and engine oil recommen- dations.
Hex Nut ,. Knob J FIGURE 2, Stop Washer / FIGURE 3. Hopper Pivot Door ASSEMBLE THIS TRUSS SCREW AND NUT FIRST Release" Bar FIGURE 4. FIGURE 5. Bolt Chute Deflector / / Release Bar 8-3/8" L.
e To attach the bag, place the opening of the bag over the chute deflector so it completely covers the chute opening. Depress the plunger on the draw- string, and pull on the drawstring until the bag .
BEFORE STARTING GAS AND OIL FILL-UP NOTE: ENGINE IS SHIPPED WITHOUT OIL FILL CRANKCASE WITH OIL BEFORE STARTING. BE VERY CAREFUL NOT TO ALLOW DIRT TO ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL Recommended SAE Viscosity Grades <llllll' 00!1o'w -%l !, 'T,,t _I_L_I.
e Pull rope with a rapid, continuous, full arm stroke, Keep a firm grip on start handle Let rope rewind slowly Do not let starter handle snap back against starter e Repeat preceding two instructions u.
No 1/2" Diameter FIGURE 12. e To lower the hopper assembly, use one hand to grasp the handle at the top of the hopper assembly and lift slightly, Pull up on the release bar, and lower the hopper assembly to the ground Release the bar'. See figure 13.
When engine is drained of all oil, replace drain plug securely_ e Refill with fresh oil Above 32 °, use oil labeled SAE 30 or 10W30 Below 32 °, use oil labeled 5W20 Capacity is approximately 1-1/4 pints Refer to "Gas and Oil Fill-Up" on page 8 e Replace dipstick.
STORAGE NEVER STORE YOUR CHIPPER- _SHREDDER INDOORS OR IN AN EN- CLOSED, POORLY VENTILATED AREA IF GASOLINE REMAINS IN THE TANK. FUMES MAY REACH AN OPEN FLAME, SPARK OR PILOT' LIGHT FROM A FUR- NACE, WATER HEATER, CLOTHES DRYER, CIGARETTE, ETC.
SERVKCE & ADJUSTMENT WARNING: ALWAYS STOP ENGINE AND DISCONNECT SPARK PLUG WIRE AND MOVE IT AWAY FROM SPARK I PLUG BEFORE PERFORMING ANY ADJUSTMENTS OR REPA RS.
Pi Sharp of Torque Wrenctl Allen Screws e When reassembling the blade, tighten to between 550 and 650 inch pounds, or lacking torque wrench, tighten securely FLAILS The flails, located inside the hous.
• Test the engine by using the chipper-shredder If engine tends to stall or die out, it usually indicates that the mixture is slightly lean and it may be nec- essary to open ( _ ) the needle valve s.
TROUBLE SHOO'rING PROBLEM POSSIBLE CAUSE(S) CORRECTIVE ACTION Engine fails to start e Fuel tank empty, or stale fuel e • Spark plug wire disconnected e e Faulty spark plug e Loss of power; oper.
SEARS CRAFTSMAN 5 H.P. CHIPPER-SHREDDER MODEL NOS. 247.797852 Repair Parts 247.797853 57 11 7 Model 59 22 35 36 17.
SEARS CRAFTSMAN 5 H.R CHIPPER-SHREDDER MODEL NOS. 247.797852 Repair Parts 247.797853 KEY NO, 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 23 24 25 26 27 28 29 3O 31 32 33 34 35 36 PART NO, 13431 .
BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NO. 130212-3250-01 Repair Parts 26 337 7 36 741 35 16 615 230 219 46 220 SEE REPAIR INS'TRt_TION MANUAL (_22 19.
BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NO. 130212-3250-01 Repair Parts 3o5__ 24 71 305 655 73 37 *REQUIRES SPECIAL TOOLS TO INSTALL. SEE REPAIR INSTRUCTION MANUAL= 2O.
BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NO. 130212-3250-01 Repair Parts 127A 96G { 124 969 9 414 153 208 153 1012 190 392 435 191 725 _ 209 527 529 11 526 21.
BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NO. 130212-3250-01 Repair Parts KEY NO, 3 5 7 8 9 10 11 12 13 14 15 16 18 19 20 21 22 23 24 25 26 27 28 29 30 31 PART NO_ 395990 297565 299819 211542 *272157 29.
BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NO. 130212-3250-01 Repair Parts KEY NO 216 2t9 220 222 223 224 227 230 256 284 298 299 304 305 306 307 308 333 335 337 346 356 358 363 373 383 392 394 414 432 433 434 435 441 467 523 524 525 526 527 528 529 PART NO.
OWNER'S MANUAL HOW TO ORDER REPAIR PARTS 5 HORSEPOWER 3 CUTTING STAGE MULCHING AND BAGGaNG CHBPPER-SHREDDER Each chipper-shredder has its own model number.
An important point after buying a device Craftsman 247.797852 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Craftsman 247.797852 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Craftsman 247.797852 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Craftsman 247.797852 you will learn all the available features of the product, as well as information on its operation. The information that you get Craftsman 247.797852 will certainly help you make a decision on the purchase.
If you already are a holder of Craftsman 247.797852, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Craftsman 247.797852.
However, one of the most important roles played by the user manual is to help in solving problems with Craftsman 247.797852. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Craftsman 247.797852 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
