Instruction/ maintenance manual of the product Undercounter Refrigerator and Freezer Pizza Preparation Table Continental Refrigerator
Go to page of 33
Operation, Inst allation and Instruction Manual For Undercounter Refrigerators and Freezers and Pizza Prep aration T ables A Division of National Refrigeration & Air Conditioning Products, Inc. 539 Dunksferry Road • Bensalem, P A 19020-5908 215-244-1400 • 1-800-523-7138 • Fax: 215-244-9579 www .
Operators Manual T able of Content s Page Receiving Y our New Model ........................................................................................3 General Information And Important Operating Fact s ..........................................
RECEIVING YOUR NEW MODEL Congratulations on your recent purchase of Continental Refrigerator superior food equipment products! When your shipment arrives, please thoroughly examine the shipping crate for any punctures, dents, or signs of rough handling.
UNCRA TING YOUR NEW MODEL The shipping container should remain on your model as protection against dents or scratches while transporting it to the actual set-up location. Remove the shipping container only at the last possible moment by following these simple steps: 1.
Important Note: T o assure maximum operating efficiency , your new “SW” series model should be located where an unrestricted air supply can circulate underneath and behind the cabinet.
FIGURE 1b MINIMUM CLEARANCE DIMENSIONS WITHOUT LEGS FLOOR LOADS The floor at the final location site must be level, free of vibration and strong enough to support the total combined weight s of your new model plus the maximum product load which might be placed into it.
INST ALLING LEGS AND LEVELING Y our new “SW” series model is supplied with adjustable type legs for leveling purposes. Each SW27, SW48, SW60 and SW72 model has four leg mounting holes on its case bottom. Legs are p acked in the accessory carton from which they must be removed and installed on the cabinet case bottom (see figure 2).
Important Note: It is extremely import ant that your new model is perfectly level for proper operation. If it is not level, the following adverse conditions will become apparent: 1. The door(s) will not be properly aligned and consequently will not provide a good seal.
FIGURE 3 CASTERS MUST BE TIGHT T O CABINET BOTT OM INST ALLING CONDENSA TE EV APORA T OR No floor drains or plumbing connections are required since all models use an automatic condensate water evaporating system.
FIGURE 4 OPTIONAL ELECTRIC CONDENSA TE EV APORA T OR INST ALLA TION REMOV AL OF DOORS AND DOOR ADJUSTMENT During installation, it may become necessary to remove the cabinet doors to facilit ate passage through narrow doorways or hallways.
FIGURE 5 DOOR ADJUSTMENT AND REMOV AL SELF-CLOSING HINGE MECHANISM MOUNTING For proper operation of the self-closing doors on all sandwich unit and prep models, the hinge mechanism must be mounted to apply tension in the direction shown in fig- ure 6.
REMOV AL AND REPLACEMENT OF HINGE MECHANISM T o remove the hinge mechanism from the door , remove the door from the cabinet as explained above. As shown in figure 6, remove the hinge plate from the hinge mechanism by removing the hinge pin screw . Also remove the horseshoe spring.
Important Note: Never use harsh detergents, cleaners, scouring powders or chemicals when cleaning your model. Failure to dry the interior surfaces after cleaning may result in a streaking or staining of the met al. Complete cleaning procedures and precautions are listed in the “periodic cleaning procedure” under the maintenance section.
208-230 VOL T , 60 HZ, 1 PHASE CONNECTION All 208-230 volt models are to be permanently connected and are provided with four (4) field wiring leads which exit the electrical console box located in the machine compartment rear , next to the compressor .
OPERA TION All cabinets must be given suf ficient time to reach normal operating temperature before placing any food inside cabinet or pans (if equipped). Refrigerators are designed to maintain an ideal cabinet and p an temperature of 38°F to 40°F (3.
PIZZA PREP TEMP ADJUSTMENT - COLDW ALL RAIL If an adjustment is necessary to maintain the coldwall rail temperature, a pressure control is located behind the front grill which controls the compressor operation and the temperature range of the rail.
DEFROST OPERA TION All freezer models are equipped with an automatic, electric defrost system consisting of an electric evaporator coil heater , evaporator drain pan heater , automatic electric defrost time clock, and defrost high limit switch.
FIGURE 7 EV APORA T OR ASSEMBL Y INTERIOR ACCESSORIES The standard interior accessory p ackage that is supplied from the factory with your new sandwich unit model consists of st andard pilaster strip s with pilaster clips (four (4)clips per shelf), and one (1) epoxy coated shelf per section.
FIGURE 8 ST ANDARD SHELF PILASTER OPTIONAL ACCESSORIES In addition to the optional heavy-duty pilaster and clip as shown in figure 9, all models are available with an overhead or double-overhead shelf. Models can even be stacked with a heavy duty st acking collar adapter kit as shown in figure 10.
FIGURE 9 OPTIONAL HEA VY -DUTY PILASTER OPTIONAL OVERHEAD OR DOUBLE-OVERHEAD SHELF All open top models are available with an optional overhead or double-overhead shelf.
T o stack your models, the following instructions should be followed: 1. Decide which model is to be on “top” and which model is to be on “bottom". 2. On “top” model, remove both bottom rear cover screws on “bottom” model, remove both top joggle clip screws with bumpers.
SAFETY PRECAUTIONS The following safety precautions should be followed when operating any appliances: Always disconnect the power cord before attempting to work on or clean any equipment. Disconnect the power cord when the appliance will be idled for a long period of time.
Precautions 1. Never use harsh detergents, cleaners, scouring powders, or chemicals when cleaning your model. 2. S trong bleaches tend to corrode many materials and should never come in contact with st ainless steel. 3. T incture of iodine, or iron should not come in contact with stainless steel.
MODEL # ____________________________Serial# ________________ Notes: ______________________________________________________________ ____________________________________________________________________ .
TROUBLESHOOTING AND SERVICING GUIDE 25 PROBLEM PROBABLE CAUSE CORRECTION Condensing unit will 1.Line Disconnected, Switch Open. 1.Close S tart Or Disconnect Switch not start - no hum. 2.Fuse Removed Or Blown. 2.Replace Fuse. 3.Overload Protector Blown.
PROBLEM PROBABLE CAUSE CORRECTION Condensing unit 1.Overload Protector . 1.See Problem # 3. runs, but shorts 2.Thermostat. 2.Differential Must Be Widened. cycles on: 3.High Pressure Cut-Out Due T o: 3. (a) Insufficient Air Supply (a) Check Air Supply T o Condenser .
PROBLEM PROBABLE CAUSE CORRECTION Product zone 1.Control Setting T oo High. 1.Adjust T -S tat. temperature too 2.Inadequate Air Circulation. 2. Rearrange Product Load T o high. Improve Air Circulation. 3.Dirty Condenser 3.Clean Condenser Coil Suction line frosted 1.
28 WIRING DIAGRAMS.
29.
30.
Continent al W arranty Procedure Our warranty is 1 year on part s and labor , and 5 years on the compressor from date of original installation on any unit inst alled af ter January 1, 1999. Any unit installed before January 1, 1999 has a warranty of 90 days labor , 1 year part s and 5 years on the compressor , from the date of installation.
32 W arranty Compressor Procedures If the compressor fails within the first (12) months of use or (20) months by the date code on the compressor , an “over-the-counter exchange” must be made through a T ecumseh or Copeland dealer .
33 Items NOT Covered Under W arranty Consult your owner's manual for det ailed information on the following (p age #'s listed beside each line item). I. Preventative Maintenance A. Dirty Condenser (20) B. General Hardware Adjustments 1. Casters/Legs (5-6) 2.
An important point after buying a device Continental Refrigerator Undercounter Refrigerator and Freezer Pizza Preparation Table (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Continental Refrigerator Undercounter Refrigerator and Freezer Pizza Preparation Table yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Continental Refrigerator Undercounter Refrigerator and Freezer Pizza Preparation Table - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Continental Refrigerator Undercounter Refrigerator and Freezer Pizza Preparation Table you will learn all the available features of the product, as well as information on its operation. The information that you get Continental Refrigerator Undercounter Refrigerator and Freezer Pizza Preparation Table will certainly help you make a decision on the purchase.
If you already are a holder of Continental Refrigerator Undercounter Refrigerator and Freezer Pizza Preparation Table, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Continental Refrigerator Undercounter Refrigerator and Freezer Pizza Preparation Table.
However, one of the most important roles played by the user manual is to help in solving problems with Continental Refrigerator Undercounter Refrigerator and Freezer Pizza Preparation Table. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Continental Refrigerator Undercounter Refrigerator and Freezer Pizza Preparation Table along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
