Instruction/ maintenance manual of the product CS2000-QD Contec
Go to page of 18
INTELLIGENT LABEL SENSORS OPERA TIONS MANU AL CS2000 & CS2000-QD C S 2 0 0 0 & C S 2 0 0 0 - Q D CS2000 & CS2000-QD CONTROL TECHNOLOGIES 2617 Fremontia Drive San Bernardino, CA 92404 Phone: 877-880-5389 F ax: 877-880-5537 www .
Table of Contents General Information Features Diagram CS2000 Quick Start CS2000-QD Quick Start Installation Mounting CS2000 Wiring CS2000-QD Wiring Operation Label Pla.
- 1 - General Information Features: • 10 to 30 VDC input - reverse polarity protected • Fast RISC microprocessor controlled • Easy one touch setup - label sensitivity easily adjusted, t.
- 2 - General Information Yellow LED: Indicates label backing (web) Push-button Red LED: Indicates output state Green LED: Indicates label + label backing Optional 6" Quick Disconnect 4 Pin Male Cable/Connector #8-32 Mounting Holes EASY SETUP WEB OUT LABEL 1.
- 3 - General Information CS2000 Quick Start: 1. Connect red wire to supply voltage 2. Connect black wire to supply common 3. For NPN Output - connect orange wire to black wire For PNP Output - connect orange wire to red wire 4. Connect white wire to your controller - refer to page 6 for wiring diagrams 5.
- 4 - General Information CS2000-QD Quick Start: 1. Plug the CS2000-QD's male connector into a suitable 4 pin female connector 2. Connect brown wire to supply voltage 3. Connect blue wire to supply common 4. For NPN Output - connect black wire to blue wire For PNP Output - connect black wire to brown wire 5.
- 5 - Installation Mounting: The CS2000 comes with 8 mounting holes allowing for many different mounting options. The holes are tapped for #8-32 screws and are 0.31" deep. We suggest using #8-32 x 3/8" stainless steel screws. Some different options are shown below.
- 6 - Installation CS2000 Wiring: The CS2000 comes with an 8' - 4 conductor cable. Refer below for wire designations. RED = 10-30 VDC BLK = Common WHT = Output ORN = NPN / PNP Output Selector Opt.
- 7 - Installation CS2000-QD Wiring: The CS2000-QD comes with a 6" quick disconnect M12 - 4 pin male cable/connector (Turck P/N RS4.4T-2). Refer below for wire designations.
ACME LABELS ACME LABELS AC ACME LABELS ACME LABELS ACME LABELS ACME LABELS - 8 - Operation Label Placement: For best results, position straight edge of label under the sensing area. Try to avoid sensing on rounded corners or other curved areas. Refer to diagram below.
- 9 - Operation LED Functions: Yellow - comes on when label backing (web) is under the sensing area Red - comes on when output is active - NPN sinking or PNP sourcing Green - comes on when.
- 10 - Adjusting Label Sensitivity Overview: The CS2000 will automatically adjust its label sensitivity, to the optimal setting, by simply depressing a push-button.
- 11 - Missing Label Compensation Overview: The CS2000 has the capability to detect a single missing label and output a stop pulse as though the label were present. In order for Missing Label Compensation to function properly the operator must first: a) have Pulse Output selected - see Program Mode (page 12) for more information.
- 12 - Program Mode Entering Program Mode: Program Mode is used to change any or all of the Operation Features. To enter Program Mode depress the push-button until the yellow and green LED's begin toggling (30 sec.), then release. The LED's will then output the current set-up configuration (and every 3 sec.
- 13 - Specifications General: Power Supply..................................................... 10-30 VDC, reverse polarity protected Power Consumption............................................ 50mA max. Output................................
- 14 - Specifications Dimensions: CS2000 0.44 11.2 0.625 1.00 25.4 0.625 15.9 79.4 3.125 50.8 15 0.59 2.00 0.22 5.6 0.75 19.1 0.50 12.7 15.9 0.09 Sensing Area 15.9 0.625 76.2 3.00 EASY SETUP WEB OUT LABEL 13.5 0.53 1.00 88.9 3.50 25.4 9.5 0.38 2.4 1. 2.
- 15 - Cleaning Instructions Cleaning Instructions: 1. Begin by removing the sensor lid's 4 screws with a 1/16" L wrench. 2. Gently lift the sensor's circuit board out by grasping the switch and pulling upward. Do not remove the insulation tape.
- 16 - Warranty Terms & Conditions Warranty: The CS2000 Label Sensor is warranteed for a period of two (2) years from the time of purchase. Control Technologies guarantees the CS2000 to be free from defects in materials or workmanship, and that, if used correctly will perform within specifications.
An important point after buying a device Contec CS2000-QD (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Contec CS2000-QD yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Contec CS2000-QD - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Contec CS2000-QD you will learn all the available features of the product, as well as information on its operation. The information that you get Contec CS2000-QD will certainly help you make a decision on the purchase.
If you already are a holder of Contec CS2000-QD, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Contec CS2000-QD.
However, one of the most important roles played by the user manual is to help in solving problems with Contec CS2000-QD. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Contec CS2000-QD along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
