Instruction/ maintenance manual of the product R500A CompuSTAR
Go to page of 12
One-Way AM Remote R500A By: Firstech, LLC. www.compustar.com FCC I D :O44J1WENR This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This devic.
Safety information Page 3 Remote Description: R500A Page 3 Remote Button Functions Page 4 Remote Coding Procedure Page 5 Locking and Unlocking the Doors Page 5 Arming and Disarming System Page 6 Trunk.
Saf e t y Inf o r m a tion 3 R emo te Butt on F unctions 4 Servicing your vehicle or loaning it to others Servicing your vehicle or loaning it to others When servicing the vehicle, like changing/checking the oil, or loaning your vehicle to someone who may not be familiar with Compustar systems, it may be best to put the system in valet mode.
Remote Coding Procedure 5 6 The remote must be coded to the system installed in the vehicle before it can be operated in any way. Listed below is the remote coding procedure, please read through the directions before beginning. Step 1 : Turn the ignition ON then OFF, five times within seven seconds.
8 Passive Locking Valet Mode 7 OPTIONAL FEA TURES/FUNCTIONS When in Valet mode, locking and unlocking the vehicle doors will be the only operations available through the remote, the system will not arm the alarm. The siren will be muted at this time as well.
9 10 To use Anti-Jacking mode, the starter kill relay must be rewired to an ignition kill, and Anti-Jacking mode must be turned on in the programming options.
12 Installation Tips and Recommendations 11 b. Connecting and insulating wires . Solder all connections. . Insulate all wires with shrink tube or electrical tape. c. Make sure that vibration or heat will not damage or otherwise alter your installation.
13 CON 1 14 CM1000A Wiring Diagram trunk Solenoid trunk Release Switch CON1-4 Red : 12v Constant Input Constant 12-volt (+) positive power input for the control module.
CON 2 15 16 < Circuit diagram > < Circuit diagram during unlock output > < Circuit diagram during lock output > The lock and unlock outputs of the CM1000A are actually two pre-wired relays that can be configured in the three following ways listed below.
18 17 No.2 Blue : Negative Starter Kill Output 250mA (-) negative output when armed. This wire will provide a (-) negative output when system is locked and armed, and is pre-wired to the starter kill relay. (Note:This wire can also be used to trigger after-market L.
20 19 No.7 Black/White : Negative Input for Optional Sensor When installing additional sensors, use this wire as the input wire to the alarm module for those sensors. When connecting more than one sensor to any input wire, you must diode isolate the output wires of each sensor.
Resetting Menu Options 22 21 You can only program one option at a time. You will have to repeat the procedure to program additional options. Please read through the procedure before beginning. 1. Enter programming by pressing the button, and the button simultaneously until the parking lights flash once.
An important point after buying a device CompuSTAR R500A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CompuSTAR R500A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CompuSTAR R500A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CompuSTAR R500A you will learn all the available features of the product, as well as information on its operation. The information that you get CompuSTAR R500A will certainly help you make a decision on the purchase.
If you already are a holder of CompuSTAR R500A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CompuSTAR R500A.
However, one of the most important roles played by the user manual is to help in solving problems with CompuSTAR R500A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CompuSTAR R500A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
