Instruction/ maintenance manual of the product V.35 Compatible Systems
Go to page of 17
Octal V .35 - 10/100 RIOP Installation Guide Comp atible Systems C orporati on 4730 W alnut Street Suite 1 02 Boulder , Co l or ad o 80301 303- 444- 9532 800- 356- 0283 http://www.
Octal V .35-10/100 RIOP Installation Guide, V ersion 1.0 Copyright© 1999, Compatible Systems C orporation All rights reserved. VSR, VSR-2, MicroRouter and CompatiV iew are trademarks of Compatible Systems Corporation. Other trademarks are the proper ty of their respective holders.
T able of Contents i Introd uction to t he Oc tal V. 35- 10 /100 RIOP 1 Chapter 1 - Network Installation 2 Connec ting t he Oc ta l V.35 -10/ 10 0 to th e Ethe rnet 2 Telco Li ne Conne ction Req uiremen ts 3 Connecting a Line Device to the V.
T able of Contents ii Required for IP Unn umbered Interface 8 Suggested fo r IP 9 IPX Pr otoc ol 9 Required for IPX 9 Suggested fo r IPX 9 Apple Talk Prot ocol 9 Requ ire d for Appl eT al k 9 Suggeste.
Introduction to the Octal V .35-10/100 RIOP 1 Introduction to the Octal V .35-10/100 RIOP The Octa l V .35-10/100 R outing In put/Outpu t Proces sor (RIOP ), as part of the VSR mu ltigi- gabit switching router , allows you to connect a local Ethernet and up to eight remote corpo rate networks.
Chapter 1 - Network Instal lation 2 Chapter 1 - Network Installation Octal V .35-10/100 RIOP Front Panel This section of the manual w ill help you install the Octal V .35-10/1 00 RIOP to connect a local Ethernet and up to eight remote corp orate networks.
Chapter 1 - Network Instal lation 3 T elco Line Co nnection Requir ements The Octal V .35-10/100 is not a line commun ications device. In order to conn ect each V .35 port to a wide area tr ansmission line, yo u must use a 56K CSU/DSU, ISDN T erminal Adapter , or T1/E1 CSU/D SU.
Chapter 2 - Quicksta rt Instructions 4 Chapter 2 - Quickstart Instructions This Quickstart chapter briefly discusses the m ajor parameters that must be set in order to use the Octal V .35 -10/100 RIOP as pa rt of you r VSR mul tigigabit switching r outer .
Chapter 2 - Quicksta rt Instructions 5 Suggested fo r IP These parameters h elp supply infor mation about the segmen t that the interface is conn ected to.
Chapter 2 - Quicksta rt Instructions 6 In CompatiV iew you must set a global p arameter and a port-specific p arameter . Suggested fo r DECnet Setting the parameters abo ve s hou ld be adequ ate for most installations . W AN Interface Configuration The default setting for all W AN interfaces on your Octal V .
Chapter 2 - Quicksta rt Instructions 7 ured using text-b ased configuration. TB : Use configure and set either the R IPV ersion keyword or the OSPFEnabl ed keyw ord in the IP W AN 0 (and/or a ny other p ort you wish to confi gure) sectio n. Add st atic rout es and a default router using the edit config IP Static command.
Chapter 2 - Quicksta rt Instructions 8 W AN Link Configur ation Required for Dedicated Line Operation Frame Rel ay i s pr esen tly sup po rt ed i n the Oc t al V .35-10/100 RIOP only via synchro nou s d edi- cated line operation. • Set Dedicated connection • Set Frame Relay connection CV : Use the Link C onfigurati on: W AN Dial og Box.
Chapter 2 - Quicksta rt Instructions 9 Suggested fo r IP These parameters h elp supply infor mation about the segmen t that the interface is conn ected to.
Chapter 2 - Quicksta rt Instructions 10 TB : Use config ur e and set ke ywords i n the AppleT alk W AN 0 (and/or any other port you wish to configure) section. DECnet Protocol Required for DE Cnet In order t o be used, D ECnet must be turned on both globally and fo r a parti cular port.
Chapter 3 - Shipping Def aults 1 1 Chapter 3 - Shipping Defaults Ethernet Interface IP Routing Defa ults • On • Addr ess: 198. 41.12 .1 • Subnet Mas k: 255.255.2 55.0 • Broadcast Address: 198.41. 12.255 • IP RIP of f IPX Routing D efaults • 802.
Chapt er 4 - LED Pat terns 12 Chapter 4 - LED Patterns Some of the LEDs on the front of the VSR multig igabit switching router serve dual functions. In addition to i ndicating certain ro uter-wide o perating conditions, they may als o display port- specific information.
Appendix A - Connector and Cable Pin Outs 13 Appendix A - Connector and Cable Pin Outs Pin Outs for HD D-Sub Male to V .35 Male Cable 1 Unused by the V .35 interfa ce circuitry . 2 Receive Line Signal Detect (RLSD) must be asserted b y the CSU/DSU when the W AN line is operational.
An important point after buying a device Compatible Systems V.35 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Compatible Systems V.35 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Compatible Systems V.35 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Compatible Systems V.35 you will learn all the available features of the product, as well as information on its operation. The information that you get Compatible Systems V.35 will certainly help you make a decision on the purchase.
If you already are a holder of Compatible Systems V.35, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Compatible Systems V.35.
However, one of the most important roles played by the user manual is to help in solving problems with Compatible Systems V.35. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Compatible Systems V.35 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
